MoTeC · Power distribution modules

MoTeC PDM30

≈ $3,240 (US retail, module only)

The MoTeC PDM30 is a 30-output solid-state power distribution module for race cars with many switched circuits. It keeps the compact case and 16 switch inputs of the PDM15 but carries eight 20 A and twenty-two 8 A protected outputs, about 100 A total, configured in MoTeC PDM Manager and reporting diagnostics over CAN.12

+12V
Illustration, not the product.

Key facts

Outputs308 × 20 A + 22 × 8 ASourced1
Inputs16 switch inputs, 0-51 VSourced1
Total output current100ASourced2
Weight270g9.5 ozSourced1
US retail price≈ $3,240Single retailer list price seen November 2026.Sourced · medium3

Suits

  • Race cars with 15 to 30 switched circuits
  • MoTeC M1 and C-series systems that need output diagnostics on the dash
  • Builds that want PDM32-like control without Autosport connector cost

What it is and where it fits

The MoTeC PDM30 replaces a car's relays, fuses and circuit breakers with 30 electronically switched and protected outputs.

MoTeC positions it as the larger sibling of the PDM15, with capability close to the professional PDM32.12

Its extra 8 A outputs suit cars with many small loads: injector and coil feeds, sensors, radios, cameras, lighting circuits and driver cooling. Heavy loads such as fuel pumps and fans go on the eight 20 A outputs.Medium14

Choose the PDM30 over the PDM32 when a waterproof Tyco-type connector is acceptable. The PDM32 adds Autosport connectors, IP67 sealing and more inputs.2

Hardware and I/O

The 20 A outputs handle 115 A typical transients and the 8 A outputs handle 60 A, which absorbs motor and lamp inrush at switch-on. MoTeC caps total output at about 100 A.12

The 16 switch inputs read 0 to 51 V with 0.2 V resolution. That is the same input count as the PDM15, so cars with many switches often move them to a CAN keypad or the ECU.Medium12

The case is 107.5 × 127.5 × 38.7 mm (4.2 × 5.0 × 1.5 in) and weighs 270 g. Signals run through a 34-pin and a 26-pin waterproof connector, and battery power lands on an M6 stud.1

Software and configuration

PDM Manager configures inputs, outputs, CAN messages and conditions, and also handles live monitoring, output tests and firmware updates. All current MoTeC PDMs use the same software.12

Outputs switch on switch inputs, CAN messages and logic, with current limits set in 1 A steps. MoTeC quotes up to 200 logic operations and functions.1

MoTeC describes uses such as automatic retries after a short, failover to a reserve pump and staged load shedding on low battery voltage. The same logic can control a driver cool suit.2

Connectivity and expansion

One CAN bus carries diagnostics, including output currents and error states, to a dash or logger.

MoTeC notes that this lets teams watch the whole electrical system by telemetry.12

MoTeC lists M1-series ECUs and C125, C127, C1212, C185, C187, C1812, CDL3, L120 and L180 dashes and loggers as compatible. When one unit is not enough, several PDMs can share the car.12

Laptop access uses the MoTeC UTC interface, which MoTeC lists as required.1

Installation notes

Wire the PDM onto a properly terminated CAN bus with at least one 100 Ω resistor, and add a CAN connector for the laptop.

MoTeC gives these as basic wiring requirements.1

MoTeC's wire guidance is 24-20 AWG for 8 A outputs and 20-16 AWG for 20 A outputs, heavier on long runs to limit voltage drop. The wire must also suit the connector terminal to crimp well.1

Generations and variants

The PDM30 (14103) and PDM15 (14104) share a case, inputs and the eight 20 A outputs.

The PDM30 adds 15 more 8 A outputs and 20 A more total current.2

The PDM32 (14107) has 32 outputs, 23 inputs, 120 A total output and Autosport connectors in a 180 × 60 × 28 mm case weighing 405 g.2

Specifications

From the maker's published data and independent sources.

Outputs

SpecValueSource
20 A outputs8, each 20 A continuous, 115 A transient (typical)1
8 A outputs22, each 8 A continuous, 60 A transient (typical)1
Current limit setting1 A steps per output1
ProtectionOver-current, short circuit and thermal overload on every output1
Total output current100 A2

Inputs, logic and communications

SpecValueSource
Switch inputs16, range 0-51 V, 0.2 V resolution1
LogicUp to 200 logic operations and functions1
CAN1 bus with full diagnostic data1
PC interfaceMoTeC UTC (#61059) required; MoTeC CAN cable not compatible1

Physical and electrical

SpecValueSource
Operating voltage30 V maximum1
Connectors34-pin and 26-pin waterproof connectors, M6 power stud1
Case size107.5 × 127.5 × 38.7 mm (4.23 × 5.02 × 1.52 in)1
Weight270 g (9.5 oz)1
EnvironmentalConformal-coated PCB; no IP code published1
Part number1410312

Strengths and limits

Facts, each cited. Not a score.

Strengths

  • Thirty protected outputs in the same 270 g case footprint as the 15-output PDM15.21
  • Current limits set per output in 1 A steps, with full diagnostic data on CAN.1
  • Same PDM Manager software and compatibility list as the rest of the MoTeC PDM range.2

Limits

  • Only 16 inputs for 30 outputs; the PDM32 has 23.2
  • Total output is 100 A, against 120 A for the PDM32.2
  • Uses waterproof Tyco-type connectors, not Autosport connectors.2
  • A separate MoTeC UTC interface is needed to connect a PC.1

Often compared with

ProductCategoryKey fact
MoTeC PDM15Power distribution modulesOutputs: 15 (8 × 20 A + 7 × 8 A)
AiM PDM32Power distribution modulesOutputs: 32 (28 high-side + 4 × 35 A configurable)
ECUMaster PMU-16Power distribution modulesOutputs: 16 (10 × 25 A + 6 × 15 A)
Haltech PD16 PDMPower distribution modulesOutputs: 16 (10 high-side, 2 half-bridge, 4 × 25 A)

Frequently asked

How many outputs does a MoTeC PDM30 have?

The PDM30 has 30 protected outputs: eight rated 20 A continuous and twenty-two rated 8 A continuous. It also has 16 switch inputs and one CAN bus. MoTeC lists about 100 A total output current, so not every output can run at its full rating at the same time.12

MoTeC PDM30 vs PDM32: which should I choose?

The PDM32 has two more outputs, 23 inputs instead of 16, 120 A total rather than 100 A, Autosport connectors and IP67 sealing. The PDM30 uses waterproof Tyco-type connectors in a squarer case. Both run the same PDM Manager software, so the choice comes down to inputs, connector standard and budget.2

How much current can a MoTeC PDM30 handle?

MoTeC lists 100 A total output current for the PDM30. Each 20 A output handles typical transients of 115 A and each 8 A output handles 60 A, which covers inrush at switch-on. Plan the continuous loads that run together so they stay within the 100 A total.12

What connectors does the MoTeC PDM30 use?

The PDM30 uses one 34-pin and one 26-pin waterproof connector for outputs, inputs and CAN, plus an M6 stud for the main battery feed. MoTeC's directory lists these as Tyco connectors. The PDM32 is the MoTeC model with Autosport connectors.12

Can you run two MoTeC PDMs in one car?

Yes. MoTeC states that multiple PDMs can be used for more complex power requirements. Each unit sits on the CAN bus and reports its own diagnostics, and all MoTeC PDMs are set up in the same PDM Manager software.2

What software configures a MoTeC PDM30?

MoTeC PDM Manager configures the PDM30. It sets inputs, outputs, CAN messages and switching conditions, monitors live values, runs output tests and updates firmware. A MoTeC UTC interface connects the laptop to the CAN bus; MoTeC states the older CAN cable is not compatible.1

Related terms

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. PDM30 product page and datasheet (part 14103) · MoTeC · vendor-doc · retrieved 2026-11-04
  2. Power Distribution Modules overview and comparison table · MoTeC · vendor-doc · retrieved 2026-11-04
  3. MoTeC PDM30 retail listing · GSpeed · reference · retrieved 2026-11-04
  4. What Is A PDM And How Is Haltech's PD16 So Different? · Dragzine · press · retrieved 2026-11-04

A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.