Cars and engines
7 factory applications
| Vehicle | Engine | Years | Part number |
|---|---|---|---|
| Mitsubishi Lancer Evolution IV (GSR, RS)Japan, export | 4G63T | 1996-1998 | TD05HR-16G6-9TWikipedia records a new twin-scroll turbo for the Evo IV.Medium23 |
| Mitsubishi Lancer Evolution V / VI | 4G63T | 1998-2001 | TD05HR-16G6-10.5T (GSR); TD05HRA-16G6-10.5T (RS)Wikipedia notes the Evo VI RS turbo used a titanium-aluminide turbine wheel.Medium32 |
| Mitsubishi Lancer Evolution VII GT-A | 4G63T | 2002-2003 | TD05-16G-9.0 (as named by Wikipedia)Medium2 |
| Mitsubishi Lancer Evolution VIII (GSR)US, Japan, Australia | 4G63T | 2003-2005 | 49378-01520 (TD05HR-16G6-9.8T); ADM single-flapper 49378-01540Low36 |
| Mitsubishi Lancer Evolution VIII MR | 4G63T | 2004-2005 | 49378-01560 (TD05HR-16G6-10.5T, single flapper)Low32 |
| Mitsubishi Lancer Evolution IX (GSR, MR) | 4G63T with MIVEC | 2005-2007 | 49378-01570 or 49378-01580 (TD05HR-16G6-10.5T); Mitsubishi 1515A054 / 1515A059Sources give both MHI numbers for the Evo IX. Full-Race lists 01580 as the stock unit; a forum list gives 01570 for the GSR.Medium453 |
| Mitsubishi Lancer Evolution IX Wagon (GT / GT-A) | 4G63T | 2005-2006 | TD05-16G-10.5 (GT manual); TD05-16G-9.0 (GT-A automatic)Medium2 |
Specifications
Wheel sizes vary by source and revision; differences are flagged.
Compressor
Turbine and housing
| Spec | Value | Source |
|---|---|---|
| Housing type | Twin-scroll (divided) turbine housing | Medium2 |
| Nozzle area by model | Evo IV 9 cm²; Evo V/VI 10.5 cm²; Evo VIII 9.8 cm²; Evo VIII MR and IX 10.5 cm²The number before T (9.8T, 10.5T) is the turbine housing nozzle area in cm². | Low3 |
| Turbine wheel material | Inconel on TD05HR; titanium aluminide on TD05HRA (RS-spec)Wikipedia credits the Evo VI RS with the first titanium-aluminide turbine wheel in a production car. | Medium32 |
| Rotation | Opposite to DSM TD05H units | Low3 |
Hardware and rating
| Spec | Value | Source |
|---|---|---|
| Wastegate | Internal; twin flapper on some USDM Evo VIII housings, single flapper on ADM Evo VIII and VIII MR | Low3 |
| Frame limits (MHI TD05) | 160,000 rpm; pressure ratio 3.0; 950 °C (1,742 °F) exhaust | 1 |
| Bearing | Journal bearingCommonly stated by rebuilders; no MHI datasheet found. | UnverifiedLow7 |
| Factory boost | Not published by Mitsubishi in the sources foundVaries by model and market; check the service manual. | UnverifiedLow2 |
What the Evo TD05HR is
The TD05HR turbo is the twin-scroll unit Mitsubishi introduced with the Lancer Evolution IV.
The Evo V carried it over with more boost through a revised ECU, and versions of it stayed on the 4G63T until the Evo IX.Medium2
Mitsubishi rated these cars at 280 PS (206 kW; 276 hp) in Japan for most of the run. Export Evo IX ratings reached 291 PS (214 kW; 287 hp).Medium2
Reading TD05HR-16G6-10.5T
TD05HR is the turbine side, 16G6 the compressor, and 10.5T the turbine housing nozzle area in square centimeters.
A smaller number spools sooner and flows less at high rpm.Low3
An extra A (TD05HRA) marks the lighter titanium-aluminide turbine wheel used on RS-spec cars. Wikipedia credits the Evo VI RS with the first such wheel in a production car.Medium32
Evo VIII vs Evo IX turbo
Owner part-number lists put the US Evo VIII GSR on a 9.8 cm² housing and the Evo VIII MR and Evo IX on 10.5 cm².
The compressor code stays 16G6.Low3
Wikipedia says the Evo IX got a revised turbocharger alongside MIVEC variable intake cam timing. Treat the turbo and the engine changes as a package when comparing the two cars.Medium2
How to identify one
Read the nameplate
Evo units carry 49378- MHI numbers, and Evo IX turbos also carry Mitsubishi numbers such as 1515A054 or 1515A059.Medium54
Check the wastegate side. Owners report twin-flapper housings on USDM Evo VIII and single-flapper housings on ADM Evo VIII and VIII MR units.Low3
Common problems
What fails, why, and the usual fix.
1Wastegate rattle and boost loss
Usual causeWorn flapper shaft bushing or a flapper that no longer seats, a common age issue on MHI internal-gate housings.
FixFit a wastegate bushing kit or a replacement housing; check for cracks at the flapper seat.Low9
2Cracks around the wastegate port
Usual causeHeat cycling of the cast turbine housing.
FixSmall surface cracks are common; replace the housing if a crack reaches the flapper seat or runs through.Low10
3Oil smoke and shaft play
Usual causeWorn bearings and seals after high mileage or poor oil supply.
FixRebuild or replace the center section; a stock-size CHRA is available from rebuilders.Low7
Upgrade paths
The routes owners take from the factory unit.
Evo VIII 9.8T → Evo IX 10.5T
Owners fit the larger 10.5 cm² Evo VIII MR or Evo IX housing for more top-end flow. It is the same 16G6 compressor, so expect a later spool and recalibrate boost and fueling.Low3
TD05HR-20G hybrid (reverse rotation)
Arashi sells a TD05HR-20G with a billet reverse-rotation wheel listed as replacing 49378-01570 and -01580. It keeps the factory manifold and downpipe locations.Low8
Larger single on an aftermarket manifold
Bigger power usually means a new manifold and a larger frame. Compare compressor maps such as the G30-770 against the 2.0 L engine's airflow target rather than headline power figures.Low1
Garrett G30-770 compressor map →Frequently asked
What turbo does the Evo 9 have?
The Evo IX uses a Mitsubishi Heavy Industries TD05HR-16G6-10.5T, a twin-scroll turbo with a 16G6 compressor and a 10.5 cm² turbine housing. Sources give MHI 49378-01580 and 49378-01570 for it, with Mitsubishi numbers 1515A054 and 1515A059. Check the nameplate on the unit you have.Medium453
What is the difference between the Evo 8 and Evo 9 turbo?
Owner part lists put the US Evo VIII GSR on a 9.8 cm² turbine housing and the Evo IX on 10.5 cm², both with the 16G6 compressor. Wikipedia describes the Evo IX turbo as revised. The larger housing trades a little spool for more flow at high rpm.Low32
What does 10.5T mean on an Evo turbo?
It is the turbine housing size: the nozzle area in square centimeters. Evo turbos came with 9, 9.8 and 10.5 cm² housings. A smaller area raises exhaust velocity for earlier boost; a larger one lowers back pressure at high rpm.Low3
What is a TD05HRA?
TD05HRA marks the RS-spec version with a lighter titanium-aluminide turbine wheel instead of the Inconel wheel in the TD05HR. Wikipedia credits the Evo VI RS with the first titanium-aluminide turbine wheel in a production car.Medium32
Can I put an Evo 9 turbo on an Evo 8?
Owners do, because both are 16G6 TD05HR units on the same 4G63T layout; the Evo IX uses the larger 10.5 cm² housing. Check wastegate flapper type and oil and water line fittings against your car, and recalibrate boost and fuel afterwards.Low3
Will an Evo turbo fit a DSM?
Not directly. Owners report the Evo IV-IX TD05HR spins the opposite way to DSM TD05H turbos, so housings and wheels do not swap and the plumbing points the wrong way. DSM owners use TD05H hybrids or a new manifold instead.Low3
Related
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
10 sources
- Turbochargers for vehicles: technical information (TD series table) · Mitsubishi Heavy Industries · oem · retrieved 2026-11-04
- Mitsubishi Lancer Evolution · Wikipedia · reference · retrieved 2026-11-04
- Evo 9 turbo into 2G (thread with Evo turbo part-number list) · DSMTuners · community · retrieved 2026-11-04
- Mitsubishi Evo IX stock turbo (49378-01580) · Full-Race Motorsports · vendor-doc · retrieved 2026-11-04
- Turbocharger for Mitsubishi Lancer Evo IX 49T78-01580 · Turbozentrum · vendor-doc · retrieved 2026-11-04
- Genuine OEM MHI TD05HR turbocharger for 2003-2005 Lancer Evolution VIII · Turbochargers Direct · vendor-doc · retrieved 2026-11-04
- TD05HR-16G6 CHRA for Mitsubishi Lancer Evo 9 / IX 4G63T · Kinugawa Turbo Systems · vendor-doc · retrieved 2026-11-04
- 2.5 in inlet TD05HR-20G for Mitsubishi Evo 9 4G63T · Arashi Dynamics · vendor-doc · retrieved 2026-11-04
- Wastegate flapper off centered · DSMTuners · community · retrieved 2026-11-04
- Crack in turbo · DSMTuners · community · retrieved 2026-11-04
Brand and model names identify the turbo and the vehicles it was fitted to; GAINS is not affiliated with their makers.

