Cars and engines
4 factory applications
| Vehicle | Engine | Years | Part number |
|---|---|---|---|
| Mitsubishi Eclipse GSX / GS-T, Eagle Talon TSi, Plymouth Laser RS Turbo (1G, manual)US | 4G63T | 1990-1994 | TD05H-14B (49178-01010, -01030, -01400, -01410)Owners report four 14B part numbers with no practical difference between them.Low34 |
| Mitsubishi Galant VR-4 (US-spec) | 4G63T | 1991-1992 | TD05H-14B (49178-01400 listed by owners as the VR-4 unit)Low34 |
| Mitsubishi Lancer Evolution III | 4G63T | 1995-1996 | —Wikipedia records the compressor growing from 65 mm to 68 mm for the Evo III; owners call this wheel the Evo III or big 16G.Medium26 |
| Alfa Romeo 164 Turbo | 2.0 Twin Spark Turbo | Not stated | TD05H-12B-6 (turbine wheel 49178-30230)Low13 |
Specifications
Wheel sizes vary by source and revision; differences are flagged.
MHI frame ratings (TD05 class)
Compressor wheels (inducer / exducer)
| Spec | Value | Source |
|---|---|---|
| 14B | 43.1 mm / 58.0 mm (1.695 in / 2.285 in)Owner-measured table. | Low6 |
| Small 16G | 46.5 mm / 60.1 mm (1.830 in / 2.365 in)Owner-measured. | Low7 |
| Big 16G / Evo III 16G | 48.1-48.3 mm / 68.0 mm (1.892-1.90 in / 2.68 in)Owners list the big 16G at 1.892 in and the Evo III at 1.90 in inducer; both share the 68 mm exducer Wikipedia gives for the Evo III. | Sources differLow762 |
| 18G (aftermarket) | 48.3-50.5 mm / 68.0 mmSources disagree on the 18G inducer (1.900 in, 50.3 mm and 50.5 mm all appear); exducer is consistently about 68 mm. | Sources differLow612 |
| 20G (aftermarket) | 52.3-52.5 mm / 68.0 mmCobb lists 52.5 mm, Kinugawa 52.3 mm inducer. | Sources differLow11 |
Turbine, housing and hardware
| Spec | Value | Source |
|---|---|---|
| Turbine | TD05H turbine wheel; 14B and 16G share the turbine sideThe TD05H prefix names the turbine side; 14B/16G name the compressor. | Low6 |
| Turbine housing | 6 cm² (14B-6) on 1G DSMs; 7 cm² housings also commonOwners give 78-11020 as the 6 cm² housing casting number. | Low54 |
| Wastegate | Internal flapper, pneumatic actuator | Low8 |
| Bearing | Journal bearing (factory)Commonly stated; no MHI datasheet found. | UnverifiedLow4 |
| Factory boost | Not published by MHI; see the vehicle service manualVaries by car and market. | UnverifiedLow1 |
What the TD05 is
The TD05 turbo sits between the TD04 and TD06 in Mitsubishi Heavy Industries' range.
MHI sizes it for 2.0-3.0 L gasoline engines and rates it to 160,000 rpm with a 3.0 pressure-ratio limit.1
Enthusiasts know it from the 4G63T. The TD05H-14B went on 1990-1994 manual DSMs and the US 1991-1992 Galant VR-4, and 16G compressors arrived with the early Lancer Evolution.Medium32
14B, 16G, 18G, 20G: reading the code
In TD05H-14B-6, TD05H is the turbine side, 14B is the compressor wheel and housing, and 6 is the turbine housing size.
Every common hybrid changes the middle code and keeps the TD05H turbine.Low56
Owner measurements show the jump clearly. A 14B is about 43 / 58 mm, a small 16G about 46.5 / 60 mm and the big or Evo III 16G about 48 / 68 mm.Low67
18G and 20G wheels keep the 68 mm exducer and grow the inducer to roughly 50 mm and 52.5 mm. Sources disagree on the exact 18G size, so measure before you buy a used unit.Low11126
How to identify a 14B or 16G
Start with the compressor housing stamping.
Owners list 49178-01010, -01030, -01400 and -01410 as 14B numbers.Low4
Then look at the compressor wheel. Owners report that a 16G has split (full and short) blades while a 14B has single blades, and the housing inlet of a big 16G is visibly larger.Low47
A TD05H on a 1G automatic usually means the turbo was swapped; those cars came with the smaller TD04-13G.Low5
TD05H vs the Evo TD05HR
From the Evolution IV, Mitsubishi moved to a twin-scroll TD05HR.
It is a different turbo, not a re-labelled 16G.Medium2
Owners warn that the later Evo turbos spin the opposite way to DSM units, so an Evo IV-IX turbo will not bolt into a DSM housing setup.Low10
Common problems
What fails, why, and the usual fix.
1Wastegate flapper off-center or rattling on decel
Usual causeThe wastegate arm and bushing walk out of the turbine housing over time.
FixTap the bushing back and check alignment, fit a wastegate bushing kit, or replace the housing.Low8
2Hairline cracks around the wastegate port
Usual causeHeat cycling of the cast-iron turbine housing.
FixOwners accept small surface cracks; scrap the housing if a crack runs through or reaches the flapper seat.Low9
3Oil on the turbine wheel or smoke
Usual causeWorn shaft seal or bearing; measurable shaft play.
FixRebuild the center section with new bearings and seals before refitting.Low9
Upgrade paths
The routes owners take from the factory unit.
14B → big 16G (Evo III 16G)
The classic DSM step: the Evo III 16G compressor wheel and housing on the TD05H turbine. It needs a larger compressor inlet and a calibration change for the extra airflow.Low62
TD05H-18G or -20G hybrid
Larger aftermarket compressor wheels with the same 68 mm exducer. Cobb's 20G pairs a 52.5 mm inducer with an 8 cm² turbine housing.Low1112
Larger single on a new manifold
Past the TD05H frame, owners fit a larger frame on a new manifold. Compare compressor maps such as the G25-660 against the engine's airflow target.Low1
Garrett G25-660 compressor map →Frequently asked
What is the difference between a 14B and a 16G?
Both use the TD05H turbine; the difference is the compressor. Owners measure a 14B at about 43 mm inducer and 58 mm exducer, a small 16G at about 46.5 / 60 mm and the Evo III 16G at about 48 / 68 mm. The larger wheel moves more air but spools later.Low67
What cars came with a TD05 turbo?
The TD05H-14B came on 1990-1994 manual Eclipse GSX and GS-T, Talon TSi and Laser RS Turbo, and on the US 1991-1992 Galant VR-4. The Lancer Evolution III used the 16G compressor. Later Evos used the twin-scroll TD05HR, which is a different unit.Medium32
How do I tell a 14B from a 16G?
Read the compressor housing number first: owners list 49178-01010, -01030, -01400 and -01410 as 14Bs. Then look at the wheel through the inlet. Owners report that a 16G has split blades and a 14B has single blades. Measure the inducer if you still are not sure.Low4
Is a TD05 bigger than a TD04?
Yes. MHI rates the TD04 frame to 190,000 rpm and a 2.9 pressure ratio for smaller engines, and the TD05 to 160,000 rpm and 3.0 for 2.0-3.0 L gasoline engines. The lower speed limit reflects the TD05's larger wheels.1
Related
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
13 sources
- Turbochargers for vehicles: technical information (TD series table) · Mitsubishi Heavy Industries · oem · retrieved 2026-11-04
- Mitsubishi Lancer Evolution · Wikipedia · reference · retrieved 2026-11-04
- Genuine OEM Mitsubishi TD05H turbocharger for Eclipse, Galant VR-4, Talon, Laser (DSM 1G 4G63) · Turbochargers Direct · vendor-doc · retrieved 2026-11-04
- TD05H turbo part numbers, 14B and 16G · DSMTuners · community · retrieved 2026-11-04
- 14B or T25 (forum thread with turbo FAQ) · DSMTuners · community · retrieved 2026-11-04
- 14B, small 16G, big 16G, Evo 16G · DSMTuners · community · retrieved 2026-11-04
- Is this a 16G? · DSMTuners · community · retrieved 2026-11-04
- Wastegate flapper off centered · DSMTuners · community · retrieved 2026-11-04
- Crack in turbo · DSMTuners · community · retrieved 2026-11-04
- Evo 9 turbo into 2G · DSMTuners · community · retrieved 2026-11-04
- COBB TD05H-20G-8 turbocharger · Speed Science (COBB product listing) · vendor-doc · retrieved 2026-11-04
- GReddy turbocharger line-up · Trust (GReddy) · vendor-doc · retrieved 2026-11-04
- 49178-30230 turbine wheel for Alfa Romeo 164 TD05H-12B-6 · LeadTurbo · vendor-doc · retrieved 2026-11-04
Brand and model names identify the turbo and the vehicles it was fitted to; GAINS is not affiliated with their makers.

