Garrett G25-660 compressor map

G-SeriesG25 frame54 mm inducer67 mm exducerModelled estimate

Map data from Garrett Motion, retrieved 2026-10-25.

The Garrett G25-660 compressor peaks at 79% efficiency around 38 lb/min and a pressure ratio of 2.3. Its map reaches a pressure ratio of about 3.9, and at a pressure ratio of 2 it flows from about 13 lb/min (surge) to 55 lb/min (choke side).

Peak efficiency
79%
island 31–44 lb/min, PR 1.9–2.7
Surge line
7–48
lb/min, from PR 1.4 to 3.9
Choke side, max flow
60
lb/min (0.453 kg/s)
Pressure-ratio reach
3.92
about 43 psi boost at sea level, before losses
Map width at PR 2
4.4×
choke flow ÷ surge flow
Outlet temp at peak island
259 °F
from 77 °F inlet, PR 2.3, 79% efficiency

Flow range

0306090120

Light band: usable flow at a pressure ratio of 2 (surge to choke side). Solid band: the 79% island. Scale 0–120 lb/min. We show figures derived from the map, not the map itself. See the maker's compressor map for the full islands and speed lines.

Surge and choke

Surge is the left-hand limit: too little flow for the pressure ratio, so air reverses through the wheel. On this map the surge line runs from about 6.8 lb/min (0.051 kg/s) at a pressure ratio of 1.4 to 48.0 lb/min (0.363 kg/s) at 3.9. Keep the full-load operating line to the right of it, with margin for transients.

Choke is the right-hand limit, where efficiency falls away and the wheel can't pass more air. The digitised choke side spans 25.5 lb/min (0.193 kg/s) to 60.0 lb/min (0.453 kg/s) across pressure ratios 1.2–3.9. It is the lowest efficiency contour the maker draws (65%), not a measured choke line.

Shaft-speed lines on the map run from 65k to 165k rpm.

Engines it suits

We ran every engine preset in the turbo matcher at three boost levels and ranked all 20 maps for each. These are the engines where this compressor came out in the top three and the whole operating line stayed on the map, with no surge or choke. Modelled estimate

15 psi, single turbo

EngineRankEfficient fromLowest surge marginPeak PR
5.0 / 302 + 5.8 / 351W · Ford1 of 203,000 rpm118%2.20
Barra 4.0 NA · Ford AU1 of 203,500 rpm74%2.20
4.6 2V · Ford1 of 203,000 rpm89%2.20
5.2 / 5.9 Magnum · Chrysler1 of 202,500 rpm156%2.20
4.6 3V (VCT) · Ford1 of 203,000 rpm84%2.20
1UZ-FE / 3UZ-FE V8 · Toyota1 of 203,500 rpm61%2.20
J35 V6 · Honda1 of 204,000 rpm39%2.20
2GR-FE / FKS V6 · Toyota1 of 204,000 rpm39%2.20

22 psi, single turbo

EngineRankEfficient fromLowest surge marginPeak PR
5.0 / 302 + 5.8 / 351W · Ford1 of 203,000 rpm102%2.69
Barra 4.0 NA · Ford AU1 of 203,500 rpm62%2.69
Barra 4.0 Turbo (XR6T / F6) · Ford AU1 of 203,500 rpm69%2.69
Buick 3800 / Ecotec 3.8 V6 · GM/Holden1 of 203,500 rpm45%2.69
VQ35DE / VQ35HR / VQ37VHR · Nissan1 of 204,000 rpm29%2.69
J35 V6 · Honda1 of 204,000 rpm29%2.69
2GR-FE / FKS V6 · Toyota1 of 204,000 rpm29%2.69
S54 (E46 M3) · BMW1 of 204,500 rpm17%2.69

30 psi, single turbo

EngineRankEfficient fromLowest surge marginPeak PR
3.5 EcoBoost V6 · Ford2 of 204,000 rpm24%3.25
S55 3.0 TT (M2C / M3 / M4) · BMW2 of 204,500 rpm20%3.25
VG30DE(TT) (Z32) · Nissan2 of 204,500 rpm5%3.25
2JZ-GE (NA, VVT-i 1998+) · Toyota2 of 204,500 rpm4%3.25
M50 / M52 / S50 / S52 · BMW2 of 205,000 rpm1%3.25
N54 3.0 TT · BMW3 of 204,500 rpm20%3.25
N55 3.0 T · BMW3 of 204,500 rpm20%3.25
6G72TT (3000GT VR-4) · Mitsubishi3 of 204,500 rpm20%3.25

Assumptions (the matcher's defaults): stock torque-curve VE shape scaled to 92% peak, full boost from 3,500 rpm to redline, 120 °F charge after the intercooler, 77 °F ambient at sea level, 1.5 psi charge-side and 0.5 psi inlet losses, gasoline. A compressor map says nothing about spool or transient response; the turbine housing decides much of that. The interactive turbo matcher opens once map review is complete.

Turbine housings

The maker's turbine flow chart for this frame lists 3 housings. Highest corrected gas flow digitised for each:

HousingMax corrected flow (lb/min)At expansion ratio
84 trim V-band 0.92 A/R24.32.75
84 trim V-band 0.72 A/R20.12.75
84 trim T25 0.49 A/R15.84.00

Expansion ratio and flow as labelled on the maker's chart. See A/R ratio for how housing size trades spool against top-end flow.

Maker's published spec

Family
G-Series
Bearing
ball bearing (G-Series family)
Compressor wheel
54 mm inducer, 67 mm exducer
Turbine housing A/R
0.49, 0.72, 0.92
Maker's engine size range
1.4L-3.0L

Compare

Same compressor map as Garrett G30-660: the compressor side matches, the turbine frame differs.

Related

How these numbers are made

Method
manual reading from the maker's published map image at 1714x2048 px, assisted by row-wise dark-pixel crossing scans on a calibrated pixel grid (axis ticks located to +/-1 px)
Accuracy
about +/-1.5% of axis span on surge, left/lower island branches and speed lines; about +/-3% of axis span on the near-choke right-hand island sides (drawn dashed by Garrett and overlapped by labels)
Flow correction
302.8 K, 96.18 kPa. Not printed on this map image (Garrett's current web maps carry no correction footnote and none was found on garrettmotion.com). Values are Garrett's long-standing convention printed on its legacy GT-series compressor maps: 545 degR (85 degF) and 13.95 psia. Treat as assumed, not maker-stated for this map. One further, unlabelled efficiency contour lies outside the 65% island (it forms the lower-right map boundary); it is omitted because its value is not printed.
Pressure-ratio basis
Not stated on the maker's map

Every figure on this page is a modelled estimate derived from that digitisation. It is not a flow-bench or dyno result and makes no power claim.

Sources

Garrett and model names are trademarks of their owners and identify the part only. No affiliation or endorsement is implied.