Toyota · 1993-97

Toyota Supra MK4 A80 Turbo (2JZ-GTE, non-VVT-i) ECU and tuning guide

The Toyota Supra MK4 A80 Turbo (2JZ-GTE, non-VVT-i) (1993-97) runs the 2JZ-GTE (non-VVT-i): 3 L I6, twin-turbo, port injection, cable throttle.

Reviewed by GAINS editorial team on 2026-11-04.

Factory ECU, pinout and chassis research on this page is shared with Toyota Supra MK4 A80 Turbo (2JZ-GTE VVT-i), Toyota Supra MK4 A80 NA (2JZ-GE).

Toyota Supra MK4 A80 Turbo (2JZ-GTE, non-VVT-i), side view
Studio render for illustration, not a photograph of a specific car.
Years1993-97
Displacement3L
LayoutI6
InductionTwin-turbo
InjectionPort injection
Cam controlnone
IgnitionWasted spark
Swap demandHigh

Part of the Toyota JZ family.

Modeled power and torque

Modelled estimate, not a dyno result.

2JZ-GTE (non-VVT-i): stock vs common buildsmodeled

Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.

Stock (factory-rated peaks; shape modeled)
010020030040050060001002003004005006007001k2k3k4k5k6khplb-ftrpm
Solid = power (hp), dashed = torque (lb-ft). Shaded bands show the modeled uncertainty. Hover for values.

Stock is anchored to the factory rating (276 hp at 5600 rpm, 318.3 lb-ft at 3600 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.

2JZ-GTE (non-VVT-i) data

Platform background

The A80 Supra (1993-2002) carries the 2JZ-GE (NA) or 2JZ-GTE sequential twin turbo. US cars use a two-connector Toyota ECM under the passenger footwell, MAF metering, low-impedance injectors with a solenoid resistor (turbo), a fuel pump ECU and, on turbo models, a TRAC sub-throttle. Turbo cars got Toyota's first 6-speed manual (developed with Getrag) and ECT-iS automatics. This page gives the 1995 US 2JZ-GTE and 1997 US 2JZ-GE ECM terminal assignments from Toyota repair manuals.

Factory ECU

Location

Passenger-side footwell under the floor carpet, behind an ECM protector

Sourced27
Connectors

Two bolt-locked waterproof connectors: A (40 positions) and B (80 positions)

Sourced2
Diagnostics
  • 1995 US: DLC1/DLC2 with Toyota hand-held tester
  • 1997 US manual: DLC3 with OBD-II scan tool
Sourced · medium28
Load strategy (US)MAF meter (VG) with turbo pressure sensor (PIM) on 2JZ-GTESourced28
Ignition outputs
  • 2JZ-GTE: six IGT outputs to an igniter
  • 2JZ-GE: single IGT for distributor ignition1997 US
Sourced27
Knock controlTwo knock sensor inputsKNK1, KNK2Sourced27
Turbo controlVSV outputs for the sequential twin-turbo valves and wastegateSourced84

The factory ECM is a conventional Toyota MAF-based unit with closed-loop narrowband control and knock feedback. Toyota's reference data lists air-fuel feedback active at steady 2,500 rpm and knock feedback active on sudden throttle, which confirms the strategy is closed loop only at light and steady load. Immobilizer fitment was not confirmed from the sources used here; check the specific market and year.

Factory ECU: harness cross-reference

From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.

Toyota 2JZ non-VVTi ECU (Supra JZA80)Part numbers not yet sourced.
ECU family
Toyota 89661-series
Applies to
JZA80 Supra 2JZ-GTE/GE non-VVTi (1993-97); manual
Not for
VVT-i JZA80 (1997+); automatic

No source-supported part number. Non-VVTi vs VVTi electronics differ significantly.

Low confidenceUnverified
Toyota 2JZ-GTE ECU (JZA80 non-VVT-i, manual)Part numbers not yet sourced.
ECU family
Toyota 2JZ-GTE
Applies to
1993-98 Supra Turbo manual
Not for
1998+ VVT-i cars (separate SKU)

USDM 1998 Turbo was VVT-i; overlap with BF29147 - confirm.

Low confidenceUnverified
Toyota 2JZ-GTE ECU (non-VVT-i, auto)Part numbers not yet sourced.
ECU family
Toyota 2JZ-GTE
Applies to
1991-98 Supra/Aristo Turbo automatic
Low confidenceUnverified

Factory ECU pinout

Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.

Toyota Supra (A80) 2JZ-GTE ECM, 1995 US (non-VVT-i)

The Toyota Supra (A80) 2JZ-GTE ECM, 1995 US (non-VVT-i) uses 2 connectors with 120 cavities. This page draws each face from the OEM figure and lists the 63 terminals the OEM table documents, with wire colours where the manual prints them.

1993-1995 (1995 US manual) · US · 2 connectors, 120 cavities · 63 terminals sourced

ECM connector E10 (A), 2JZ-GTE 1995 US40 cavities · 13 terminals listed · 40 cavities, 4x10; rows 1 and 3 offset by half a pitch.

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedECU header side, as drawn in the OEM figure. Side confidence: medium.
Toyota Supra (A80) 2JZ-GTE ECM, 1995 US (non-VVT-i): ECM connector E10 (A), 2JZ-GTE 1995 USLock / keyA10: no terminal listedA10A9: no terminal listedA9A8: no terminal listedA8A7: no terminal listedA7A6: W, check engine warning lampA6A5: no terminal listedA5A4: no terminal listedA4A3: no terminal listedA3A2: SP1, vehicle speed sensorA2A1: IGSW, ignition switch signalA1A20: TE1, diagnostic test terminalA20A19: TE2, diagnostic test terminalA19A18: no terminal listedA18A17: no terminal listedA17A16: no terminal listedA16A15: ELS, electrical load signal (defogger and tail lights)A15A14: no terminal listedA14A13: no terminal listedA13A12: OD1, overdrive/transmission ECU linkA12A11: no terminal listedA11A30: no terminal listedA30A29: no terminal listedA29A28: no terminal listedA28A27: no terminal listedA27A26: no terminal listedA26A25: no terminal listedA25A24: M-REL, EFI main relay controlA24A23: ACMG, A/C magnetic clutch controlA23A22: FPC, fuel pump control signal to fuel pump ECUA22A21: no terminal listedA21A40: no terminal listedA40A39: no terminal listedA39A38: no terminal listedA38A37: no terminal listedA37A36: no terminal listedA36A35: no terminal listedA35A34: A/C, air conditioning switch/amplifier signalA34A33: BATT, battery backup supply (always 9-14 V)A33A32: no terminal listedA32A31: +B, ECM main power from EFI main relayA31
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
A1IGSW, ignition switch signalPower—
A2SP1, vehicle speed sensorSensor signal—
A6W, check engine warning lampOutputs— (medium confidence)
A12OD1, overdrive/transmission ECU linkComms / diag— (medium confidence)
A15ELS, electrical load signal (defogger and tail lights)Sensor signal—
A19TE2, diagnostic test terminalComms / diag— (medium confidence)
A20TE1, diagnostic test terminalComms / diag— (medium confidence)
A22FPC, fuel pump control signal to fuel pump ECUSensor signal—
A23ACMG, A/C magnetic clutch controlOutputs—
A24M-REL, EFI main relay controlOutputs—
A31+B, ECM main power from EFI main relayOutputs—
A33BATT, battery backup supply (always 9-14 V)Power—
A34A/C, air conditioning switch/amplifier signalSensor signal—

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (medium confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

ECM connector E9 (B), 2JZ-GTE 1995 US80 cavities · 50 terminals listed · 80 cavities in two 4x10 blocks either side of the connector bolt; rows 1 and 3 are offset by half a pitch in the OEM drawing.

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedECU header side, as drawn in the OEM figure. Side confidence: medium.
Toyota Supra (A80) 2JZ-GTE ECM, 1995 US (non-VVT-i): ECM connector E9 (B), 2JZ-GTE 1995 USB20: #10, injector cylinder 1B20B19: #20, injector cylinder 2B19B18: #30, injector cylinder 3B18B17: #40, injector cylinder 4B17B16: #50, injector cylinder 5B16B15: #60, injector cylinder 6B15B14: no terminal listedB14B13: no terminal listedB13B12: no terminal listedB12B11: no terminal listedB11B10: no terminal listedB10B9: no terminal listedB9B8: no terminal listedB8B7: NE-, crankshaft position sensor returnB7B6: G1-, camshaft position sensor 1 returnB6B5: G2-, camshaft position sensor 2 returnB5B4: no terminal listedB4B3: no terminal listedB3B2: no terminal listedB2B1: no terminal listedB1B40: VSV1 output (turbo system VSV; valve assignment not stated in the terminal table)B40B39: VSV2 output (turbo system VSV; valve assignment not stated in the terminal table)B39B38: VSV3 output (turbo system VSV; valve assignment not stated in the terminal table)B38B37: no terminal listedB37B36: no terminal listedB36B35: ISC1, idle speed control valve phase 1B35B34: ISC2, idle speed control valve phase 2B34B33: ISC3, idle speed control valve phase 3B33B32: ISC4, idle speed control valve phase 4B32B31: no terminal listedB31B30: no terminal listedB30B29: no terminal listedB29B28: E21, MAF meter signal groundB28B27: NE, crankshaft position sensor signalB27B26: G1, camshaft position sensor 1 signalB26B25: G2, camshaft position sensor 2 signalB25B24: no terminal listedB24B23: no terminal listedB23B22: no terminal listedB22B21: no terminal listedB21B60: no terminal listedB60B59: no terminal listedB59B58: IGF, ignition confirmation from igniterB58B57: IGT1, igniter trigger cylinder 1B57B56: IGT2, igniter trigger cylinder 2B56B55: IGT3, igniter trigger cylinder 3B55B54: IGT4, igniter trigger cylinder 4B54B53: IGT5, igniter trigger cylinder 5B53B52: IGT6, igniter trigger cylinder 6B52B51: no terminal listedB51B50: KNK1, knock sensor 1B50B49: KNK2, knock sensor 2B49B48: OX1, oxygen sensor 1 signalB48B47: OX2, oxygen sensor 2 signalB47B46: no terminal listedB46B45: THA, intake air temperature (in MAF meter)B45B44: THW, engine coolant temperature sensorB44B43: VTA1, main throttle position sensorB43B42: VTA2, sub-throttle (TRAC) position sensorB42B41: VCC, 5 V sensor supplyB41B80: E01, power ground (injector and actuator return)B80B79: no terminal listedB79B78: no terminal listedB78B77: STA, starter signalB77B76: NSW, park/neutral position switchB76B75: EGR, EGR VSV controlB75B74: EVAP, EVAP VSV controlB74B73: FPU, fuel pressure up VSV (hot restart)B73B72: HT2, oxygen sensor 2 heater controlB72B71: HT1, oxygen sensor 1 heater controlB71B70: no terminal listedB70B69: E1, ECM groundB69B68: no terminal listedB68B67: no terminal listedB67B66: VG, mass air flow meter signalB66B65: E2, sensor groundB65B64: IDL1, main throttle idle contactB64B63: IDL2, sub-throttle (TRAC) idle contactB63B62: PIM (printed PM1), turbo pressure sensor signalB62B61: no terminal listedB61
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
B5G2-, camshaft position sensor 2 returnCrank / cam—
B6G1-, camshaft position sensor 1 returnCrank / cam—
B7NE-, crankshaft position sensor returnCrank / cam—
B15#60, injector cylinder 6Injector—
B16#50, injector cylinder 5Injector—
B17#40, injector cylinder 4Injector—
B18#30, injector cylinder 3Injector—
B19#20, injector cylinder 2Injector—
B20#10, injector cylinder 1Injector—
B25G2, camshaft position sensor 2 signalCrank / cam—
B26G1, camshaft position sensor 1 signalCrank / cam—
B27NE, crankshaft position sensor signalCrank / cam—
B28E21, MAF meter signal groundSensor 5 V / ground—
B32ISC4, idle speed control valve phase 4Outputs—
B33ISC3, idle speed control valve phase 3Outputs—
B34ISC2, idle speed control valve phase 2Outputs—
B35ISC1, idle speed control valve phase 1Outputs—
B38VSV3 output (turbo system VSV; valve assignment not stated in the terminal table)Outputs—
B39VSV2 output (turbo system VSV; valve assignment not stated in the terminal table)Outputs—
B40VSV1 output (turbo system VSV; valve assignment not stated in the terminal table)Outputs—
B41VCC, 5 V sensor supplySensor 5 V / ground—
B42VTA2, sub-throttle (TRAC) position sensorSensor signal—
B43VTA1, main throttle position sensorSensor signal—
B44THW, engine coolant temperature sensorSensor signal—
B45THA, intake air temperature (in MAF meter)Sensor signal—
B47OX2, oxygen sensor 2 signalSensor signal—
B48OX1, oxygen sensor 1 signalSensor signal—
B49KNK2, knock sensor 2Sensor signal—
B50KNK1, knock sensor 1Sensor signal—
B52IGT6, igniter trigger cylinder 6Ignition—
B53IGT5, igniter trigger cylinder 5Ignition—
B54IGT4, igniter trigger cylinder 4Ignition—
B55IGT3, igniter trigger cylinder 3Ignition—
B56IGT2, igniter trigger cylinder 2Ignition—
B57IGT1, igniter trigger cylinder 1Ignition—
B58IGF, ignition confirmation from igniterIgnition—
B62PIM (printed PM1), turbo pressure sensor signalSensor signal—
B63IDL2, sub-throttle (TRAC) idle contactSensor signal—
B64IDL1, main throttle idle contactSensor signal—
B65E2, sensor groundSensor 5 V / ground—
B66VG, mass air flow meter signalSensor signal—
B69E1, ECM groundGround—
B71HT1, oxygen sensor 1 heater controlOutputs—
B72HT2, oxygen sensor 2 heater controlOutputs—
B73FPU, fuel pressure up VSV (hot restart)Outputs—
B74EVAP, EVAP VSV controlOutputs—
B75EGR, EGR VSV controlOutputs—
B76NSW, park/neutral position switchSensor signal—
B77STA, starter signalSensor signal—
B80E01, power ground (injector and actuator return)Ground—

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (medium confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

Coverage, year splits and safety

Covers the 1995 US 2JZ-GTE (non-VVT-i) ECM connectors E10 (A) and E9 (B) from the 1995 repair manual's 'Standard value of ECM terminals' table, which lists only the terminals it tests. 1996-98 US, VVT-i and Japanese-market ECUs are not covered.

Source notes: 2JZ-GTE rows are from the 1995 US-model repair manual 'Standard value of ECM terminals' (connectors E9 'B' and E10 'A'); that table gives terminal symbols but not wire colours or every pin. 2JZ-GE rows with wire colours are from the 1997 RM502U 'Terminals of ECM' table (US, OBD-II) as reproduced by toyota-supra.de; wire colours shown are the terminal-side colour. Function descriptions for TE1/TE2, W, OD1 and SDL are interpretations of Toyota's terminal symbols. Japanese-market ECUs (JZA80 RZ/GZ, Aristo) and 1996-98 US 2JZ-GTE ECUs are not covered; obtain the matching Toyota EWD/repair manual (e.g. 1997 Supra RM502U and its EWD) before wiring.

Safety: disconnect the battery before working on the ECU harness, and confirm each terminal with a meter against your own car's manual before cutting or pinning wires.

All factory ECU pinouts →

Plug-and-play harness

Route for this carS3 plug-in harness
1 · S3 plug-in2 · Factory-connector adapter3 · Wire-in

A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.

MakerHarnessFitsLink
Toyota Supra JZA80HT-186369JZA80 Supra 2JZ-GTE/GE non-VVTi (1993-97); manual$535LowestMaker ↗
Manual 1993 - 1998 Toyota Supra 2JZ-GTEBF29087-S31993-98 Supra Turbo manual$1,200Maker ↗
Auto 1993 - 1998 Toyota Supra 2JZ-GTEBF29188-S31991-98 Supra/Aristo Turbo automatic$1,200Maker ↗
Wire-inUniversal flying lead or re-terminated factory harnessAny engine (terminate to ECU2's two Superseal 34 connectors)Universal harness from $405Maker ↗

Nexus S3 Plug n Play Adapter Harness Toyota Supra JZA80

$535USD list · excl. tax
Plug-and-playManual onlyOff-road / competition onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
Toyota 2JZ non-VVTi ECU (Supra JZA80)
ECU
Toyota 89661-series
Confidence
low

No source-supported part number. Non-VVTi vs VVTi electronics differ significantly.

Fits
JZA80 Supra 2JZ-GTE/GE non-VVTi (1993-97); manual
Exclusions
VVT-i JZA80 (1997+); automatic
SKU
HT-186369
Maker fitment
Toyota Supra JZA80 2JZ non-VVTi; manual only
Maker notes
kit HT-213324 USD 2800

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1993 - 1998 Toyota Supra 2JZ-GTE

$1,200USD list
Plug-and-playManual onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
Toyota 2JZ-GTE ECU (JZA80 non-VVT-i, manual)
ECU
Toyota 2JZ-GTE
Confidence
low

USDM 1998 Turbo was VVT-i; overlap with BF29147 - confirm.

Fits
1993-98 Supra Turbo manual
Exclusions
1998+ VVT-i cars (separate SKU)
SKU
BF29087-S3
Maker fitment
Toyota Supra 2JZ-GTE (Manual); selector years 1993-1998; SKU label: Manual 1993 - 1998 Toyota Supra 2JZ-GTE
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); manual

Boomslang plug-and-play harness for Haltech Nexus S3 - Auto 1993 - 1998 Toyota Supra 2JZ-GTE

$1,200USD list
Plug-and-playAuto onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
Toyota 2JZ-GTE ECU (non-VVT-i, auto)
ECU
Toyota 2JZ-GTE
Confidence
low
Fits
1991-98 Supra/Aristo Turbo automatic
SKU
BF29188-S3
Maker fitment
Toyota Aristo 2JZ-GTE; Toyota Supra 2JZ-GTE (Auto); selector years 1991-1998; SKU label: Auto 1993 - 1998 Toyota Supra 2JZ-GTE
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); auto

Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.

Your GAINS system for this car · pre-release

ECU2 for the Supra MK4 A80

Planned with the same rules as the configurator for this car's 6 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.

Toyota Supra MK4 A80 Turbo (2JZ-GTE, non-VVT-i) studio render
Supra MK4 A80
  • ECU2Engine controller

    6 cyl · port injection · cable throttle

    Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.

    in designEst. availability: April 2027

    Price TBA

Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →

Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →

What you get

  • A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
  • Faults in plain words"Coolant temp sensor open circuit.
  • S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
  • Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
  • GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.

How it wires in

  1. Haltech S3 plug-in harness1 listed · from $535 USD listHT-186369
  2. Factory-connector → S3 adapter2 listed · from $1,200 USD list
  3. Wire-inAlways possible

Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓

ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.

How GAINS approaches the Supra MK4 A80

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    Boost controlgated

    A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.

  4. 4
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  5. 5
    Factory load sensingfactory reference

    What the factory ECU measures load with: varies by year/market (low confidence); Forum consensus only: JDM 2JZ-GTE MAP (D-type); US/EU Supra Turbo uses an air-flow meter (aftermarket MAP-ECU sold to remove it) with MAP part 89421-20200 used for boost. No OEM doc read; Karman-vortex vs hot-wire on US car unconfirmed.

  6. 6
    Wideband sensorhardware

    Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller

  7. 7
    Bottom end and head sealingfactory reference

    Reported: Stock cast pistons are commonly reported as the first bottom-end limit; the oil pump drive is reported (MotoIQ) as the first part to suffer from torsional vibration at high rpm. (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Drivetrain

Manual (turbo)6-speed manual, Toyota's first, developed with Getrag (V160)Sourced69
Manual (NA)5-speed manualW58Sourced69
Automatic
  • 4-speed ECT-S (NA, Japan) / ECT-iS with manual-shift mode (turbo, Japan)
  • A340E in US repair manual
Sourced69
Brakes and traction
  • 4-channel ABS with lateral G sensing standard on Japanese turbo models
  • TRAC traction control with sub-throttle on US turbo
Sourced62
LayoutFront-engine, rear-wheel drive, 2+2 hatchback coupeSourced5

Chassis integration

TRAC sub-throttle

Second throttle valve with its own position sensor (VTA2) and idle contact (IDL2) wired to the engine ECM

Sourced2
Fuel pumpFuel pump ECU drives the pump on ECM command (FPC)Sourced82
Vehicle speedSP1 speed signal input to the ECMSourced27
A/CA/C signal (A/C) input and magnetic clutch output (ACMG)Sourced27
Electrical loadELS input from defogger and tail-light circuitsSourced27
Tachometer test pointTachometer connects to the IG- terminal of DLC1 (1995)Sourced · medium3

When fitting a standalone ECU, the TRAC sub-throttle is normally fixed open or removed, the ECM's A/C and speed inputs must be recreated if those features are to keep working, and the fuel pump ECU needs either an FPC signal or a bypass. The EFI main relay is switched by the ECM (M-REL), so a replacement ECU must provide or bypass that control.

Tuning notes

Stock boost check (US, 1995)

61-75 kPa (8.8-10.8 psi) at 5,600 rpm or above, full throttle, first gear

Sourced4
Injectors (US 2JZ-GTE)

Approx. 1.95 ohm, with approx. 6 ohm solenoid resistor per circuit

Sourced8
Fuel pressure (US 2JZ-GTE)226-275 kPa with regulator vacuum disconnectedSourced8
Rated output (Japan)
ItemPowerTorque
2JZ-GTE280 PS at 5,600 rpm44.0 kgm at 3,600 rpm
2JZ-GE225 PS at 6,000 rpm—
Sourced65

On the turbo car, the usual sequence is boost and fuel first (pump wiring, injectors), then either a piggyback for the factory ECM or a full standalone, often combined with a single-turbo conversion that deletes the sequential VSV network. Keep knock monitoring active and log wideband lambda; the factory narrowband sensors give no useful information at full load.

Popular swaps

NA to turbo
  • 2JZ-GE cars are commonly converted to 2JZ-GTE
  • The turbo engine adds igniter, VSV, boost sensor and fuel system differences to account for
Sourced · medium87

NA-to-turbo conversions on the A80 need the turbo engine's ECM and harness or a standalone, the turbo fuel system (injectors, resistor pack or high-impedance replacements, pump ECU), intercooler piping, and usually the V160 or a strengthened gearbox. Alternative-engine swaps into the A80 are possible but are outside the scope of OEM documentation.

Other Supra MK4 A80 guides

GAINS on the Supra MK4 A80

ECU2

ECU2Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

Where is the ECU on a MK4 Supra?

Under the passenger-side floor carpet behind a protective cover. It uses two bolt-locked connectors (A and B).27

Does the US MK4 Supra Turbo use a MAF or a MAP sensor?

A MAF meter with built-in air temperature sensor, plus a turbo pressure sensor read by the ECM.82

What is stock boost on a MK4 Supra Turbo?

Toyota's 1995 US check value is 61-75 kPa (about 8.8-10.8 psi) at 5,600 rpm or above at full throttle in first gear.4

Which ECU pins drive the 2JZ-GTE ignition?

On the 1995 US ECM, IGT1 to IGT6 are terminals B57 to B52 and the IGF confirmation is B58.2

Which transmissions came in the A80 Supra?

Turbo cars could have a 6-speed manual developed with Getrag; NA cars a 5-speed manual; automatics were 4-speed (ECT-S/ECT-iS in Japan, A340E in US manuals).69

Does the MK4 Supra Turbo have drive-by-wire?

The 1995 US turbo has a cable main throttle plus an ECM-monitored TRAC sub-throttle; the 2JZ-GTE VVT-i engine introduced electronic throttle control in 1997 per AutoSpeed.21

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. The Toyota JZ Engine Guide (Michael Knowling) · AutoSpeed (Web Publications Pty Ltd), archived copy · press · retrieved 2026-10-25
  2. Toyota Supra repair manual (1995 model), 2JZ-GTE engine troubleshooting: standard value of ECM terminals and ECM data (pages EG-510 to EG-513) · Toyota Motor Corporation (page images reproduced by toyota-supra.de) · service-manual · retrieved 2026-10-25
  3. Toyota Supra repair manual (1995 model), SFI system 2JZ-GTE (pages EG-258 on) · Toyota Motor Corporation (page images reproduced by toyota-supra.de) · service-manual · retrieved 2026-10-25
  4. Toyota Supra repair manual (1995 model), Turbocharger system 2JZ-GTE (pages EG-140 to EG-162) · Toyota Motor Corporation (page images reproduced by toyota-supra.de) · service-manual · retrieved 2026-10-25
  5. 75 Years of Toyota: Vehicle lineage, Supra (JZA80) · Toyota Motor Corporation · oem · retrieved 2026-10-25
  6. Toyota launches all-new Supra (press release, 24 May 1993) · Toyota Motor Corporation · press · retrieved 2026-10-25
  7. Toyota Supra A80 repair manual: Terminals of ECM, 2JZ-GE engine (based on RM502U, 1997) · Toyota Motor Corporation (reproduced by toyota-supra.de) · service-manual · retrieved 2026-10-25
  8. 1997 Toyota Supra Repair Manual (RM502U), SFI (2JZ-GTE) section · Toyota Motor Corporation (copy hosted at personal.tcu.edu) · service-manual · retrieved 2026-10-25
  9. Toyota Supra A80 repair manual index (sections incl. W58 and V160 manual transmissions, A340E automatic, TRAC, ABS) · Toyota Motor Corporation (reproduced by toyota-supra.de) · service-manual · retrieved 2026-10-25

Catalog data and evidence

  • Catalog data, not yet expert-reviewed.
  • No vehicle photos: illustrations only until licensed imagery is available.
  1. E-932 Haltech S3 adapter harness page (sourced, high confidence)
  2. E-934 Boomslang identity (sourced, high confidence)
  3. E-935 Boomslang S3 catalog size (sourced, high confidence)
  4. E-900 Haltech Nexus S3 catalog (sourced, high confidence)
  5. E-941 S3 engine harness availability (inferred, medium confidence)