GM · Piezoelectric (AC)

GM 12623730 knock sensor (Gen IV LS)

GM 12623730

GM 12623730 is the knock sensor for Gen IV LS engines, from the 5.3 and 6.0 trucks to the LS3, LS7, LSA and LS9. Gen IV mounts its sensors low on each side of the block toward the rear, where Gen III put them in the valley under the intake. Worn junkyard or cheap sensors are a known source of false (ghost) knock.Medium624

Key specifications

Measures: Block vibration in the knock band. Output: Piezoelectric (AC).

LocationLower block, both sides, toward the rear (Gen IV)Sourced · medium6
CountTwoone per bankSourced · medium6
Sensitivity and frequency responseUnverifiedNot in a public GM document we could archive.Researched, unverified
Part numberMakerNote
12623730GMMedium246

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedLS engines use two knock sensors. The ECU2 has one KNOCK pin and the ECU2 lists two; the dual-knock pin assignment is still open.Medium710
Haltech (Elite / Nexus)Configurable (generic input)One of 2 knock inputs (Nexus R3).11
Link (G4X)Configurable (generic input)One of 2 knock inputs (G4X FuryX).12
MoTeC (M1)Configurable (generic input)One of 4 knock inputs (M150).13
ECUMaster (EMU Black)Configurable (generic input)One of 2 knock inputs.14
AEM (Infinity)Configurable (generic input)2-channel knock input.15
MaxxECUConfigurable (generic input)One of 2 knock inputs (RACE).16
Holley (Terminator X / EFI)Configurable (generic input)One of 2 knock inputs. Holley notes knock control is not enabled in the Terminator X starting configuration.17

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

The maker does not publish a data sheet, drawing or CAD model for this part that we could find.

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

Two shielded signal wires per sensor to the ECU's knock input; drain at the ECU end only.Medium97

Failure modes and checks

Ghost knock

Likely cause Tired used sensors or generic replacements

Check Fit known-good sensors before changing calibration.Medium6

Knock code on one bank

Likely cause Damaged harness under the intake

Check Check continuity from each sensor to the ECU.Medium1

Frequently asked

Where are the knock sensors on a Gen IV LS?

Low on both sides of the block toward the rear. Gen III engines put them in the valley under the intake manifold, where water can collect.Medium6

Why does my LS show knock that is not there?

Old junkyard or low-quality sensors are a common cause of ghost knock. Replace them before adjusting timing.Medium6

Related

Use it with GAINS

GM 12623730 knock sensor (Gen IV LS) on GAINS hardware

ECU2KNOCK

Pins
On the ECU2 pin map
Pull-up
Not used
Shielding
Shielded, drain at the ECU end only

Shielded twisted pair, drain at the ECU end only. One knock input; two-sensor V-engine mapping to be confirmed.Medium7

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.78

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

17 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. OEM sensors GM Camaro: GM part numbers for Camaro knock/crank/cam/MAF/MAP/O2 sensors by year and engine (L98, LT1, LS1, LS3, LSA, LT1 · gmpartsgiant.com · oem · retrieved 2026-10-25
  3. OEM sensors GM Corvette: GM part numbers for Corvette knock/crank/cam/MAP/MAF/O2 1984-2024 (L98, LT1, LS1, LS6, LS2, LS3, LS7, LS9, LT1 · gmpartsgiant.com · oem · retrieved 2026-10-25
  4. OEM sensors GM Silverado: GM part numbers for Silverado gas V8 knock/MAP/MAF/O2/crank/cam 1999-2024 (Gen III/IV/V truck) · gmpartsgiant.com · oem · retrieved 2026-10-25
  5. GM sensors retailer catalogue: Genuine GM / Delphi / NTK / Denso / ACDelco LS and LT sensor listings with fitment titles (24x/58x crank, cam, · michiganmotorsports.com · vendor-doc · retrieved 2026-10-25
  6. Dialing in LS sensors for various generations with Michigan Motorsports · EngineLabs · press · retrieved 2026-10-27
  7. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  8. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  9. Shielded cable · Wikipedia · reference · retrieved 2026-10-27
  10. internal GAINS internal: ECU2 concept (hardware/mini-duo/CONCEPT.md §2)
  11. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-10-27
  12. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  13. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  14. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  15. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  16. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.