Hitachi · HT family · Gasoline

Hitachi HT18 (Mazda RX-7 FC Turbo II)

HT18HT18S-2SFC Turbo II turbo13B-T turboHitachi twin-scroll turbo13B-T rotaryS4: valve-fed scrollsS5: divided manifoldFD successor: sequential HT12 twins

The Hitachi HT18 is the twin-scroll turbo on the 13B-T rotary in the second-generation FC RX-7 Turbo II. Parts sellers list the 1986-1988 Series 4 unit as the HT18S-2S. Wikipedia says the Series 4 fed its twin scrolls through a two-stage valve and the 1989-1991 Series 5 used a divided manifold. The later FD RX-7 used two smaller Hitachi HT12 turbos in sequence.Medium125

CompressorjournalTwin-scroll turbine
Illustration of the layout, not the part.

Cars and engines

3 factory applications

VehicleEngineYearsPart number
Mazda RX-7 Turbo II (FC3S, Series 4)13B-T1986-1988HT18S-2SMazda rated 185 PS (136 kW) per Wikipedia.Medium21
Mazda RX-7 Turbo II (FC3S, Series 5)13B-T1989-1991—Revised turbo with a divided manifold; 200 PS (147 kW).Medium1
Mazda Luce Turbo-II13B-T1986-1991—Wikipedia lists the 13B-T in the Luce at 185 PS (136 kW); turbo specification not confirmed.Low1

Specifications

Wheel sizes vary by source and revision; differences are flagged.

FC HT18

SpecValueSource
Turbine housingTwin scrollMedium13
Scroll feed (Series 4)Two-stage mechanically actuated valveMedium1
Scroll feed (Series 5)Divided exhaust manifoldMedium1
CoolingAir-cooled or water-cooledA Mazda history page describes an air-cooled twin-scroll turbo; other sources say water-cooled.Sources differLow43
Wheel sizesNot found in a reliable sourceNo Hitachi or Mazda figures found.UnverifiedLow2

FD HT12 (for comparison)

SpecValueSource
LayoutTwo Hitachi HT12 turbos, sequential; primary only until about 4,500 rpmMedium15
Compressor wheel57 mm, 10 bladesMedium5
Turbine wheel51 mm, 9 bladesMedium5

What the HT18 is

The FC RX-7 turbo is a Hitachi HT18, a twin-scroll unit on the 1.3 L twin-rotor 13B-T in the Turbo II.

Parts sellers list the 1986-1988 Series 4 version as the HT18S-2S.Medium231

Mazda rated the Series 4 Turbo II at 185 PS (136 kW) and the Series 5 at 200 PS (147 kW), according to Wikipedia.Medium1

Series 4 vs Series 5

On the 1986-1988 Series 4, a two-stage mechanically actuated valve fed the turbo's twin scrolls.

For 1989-1991 Mazda used a better turbo design with a divided manifold feeding the scrolls directly.Medium1

Because the manifold and turbo changed together, treat S4 and S5 units as different parts and match the manifold when swapping.Low1

The FD RX-7's sequential HT12 twins

The 1992-2002 FD RX-7's 13B-REW used two Hitachi HT12 turbos sequentially.

Wikipedia calls it the first volume-production sequential twin-turbo system; only the primary turbo boosts until about 4,500 rpm.Medium15

MotoIQ measured the HT12 compressor wheels at 57 mm with 10 blades and the turbine wheels at 51 mm with 9 blades. Its writer puts the stock twins' limit around 350 whp, an author estimate rather than a Mazda figure.Medium5

Heat and safety

Turbo and exhaust parts stay hot long after shutdown.

Check every fuel and vacuum line near the turbo for heat damage whenever it is serviced, and keep a fire extinguisher at hand when first starting after turbo work.Low3

Common problems

What fails, why, and the usual fix.

  1. 1Second turbo on an FD arriving late or not at all

    Usual cause

    Sequential control valves and vacuum lines aging or leaking.

    Fix

    Test the vacuum system and control solenoids before replacing turbos; many owners simplify to a single turbo.Low15

  2. 2Wrong FC turbo for the manifold

    Usual cause

    Series 4 and Series 5 use different scroll-feed arrangements.

    Fix

    Match the turbo to the manifold generation.Low1

Upgrade paths

The routes owners take from the factory unit.

Twins to single

FD sequential twins → single turbo

MotoIQ's FD build argues a modern single turbo is simpler and more reliable than the 30-year-old twins. Compare maps such as the EFR 7163 against the 13B-REW's airflow target.Medium5

BorgWarner EFR 7163 compressor map →
Big single

FC HT18 → larger single on a new manifold

FC owners chasing more airflow fit a larger turbo on an aftermarket manifold. Compare maps such as the EFR 6758 against the 13B-T's airflow target.Low3

BorgWarner EFR 6758 compressor map →

Frequently asked

What turbo is on the FC RX-7 Turbo II?

A Hitachi HT18 twin-scroll turbo on the 13B-T rotary. Parts sellers list the 1986-1988 Series 4 unit as the HT18S-2S; the 1989-1991 Series 5 used a revised design with a divided manifold.Medium21

What is the difference between the S4 and S5 RX-7 turbo?

Wikipedia says the Series 4 fed its twin-scroll turbo through a two-stage mechanically actuated valve, while the Series 5 used a better turbo with a divided manifold feeding the scrolls. Mazda's rating rose from 185 PS (136 kW) to 200 PS (147 kW).Medium1

What turbos does the FD RX-7 have?

Two Hitachi HT12 turbos working sequentially, with only the primary making boost until about 4,500 rpm. MotoIQ measured 57 mm, 10-blade compressor wheels and 51 mm, 9-blade turbine wheels on them.Medium51

Can the FD sequential twins be upgraded?

Yes, but most owners go single. MotoIQ's FD build says modified twins tend to be laggier for a modest gain and argues a modern single turbo is simpler and more reliable. A single needs a new manifold and a matching fuel and calibration setup.Medium5

Related

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Mazda Wankel engine (13B-T, 13B-REW) · Wikipedia · reference · retrieved 2026-11-04
  2. 86-88 Mazda RX7 Turbo II FC S4 1.3L 13B HT18S-2S turbocharger (core) · Import A Part · vendor-doc · retrieved 2026-11-04
  3. Mazda RX-7 FC tuning guide · Fast Car · press · retrieved 2026-11-04
  4. History of craft spirit (RX-7) · Mazda · oem · retrieved 2026-11-04
  5. Project FD RX7 restomod, part 11: engine disassembly (Billy Johnson) · MotoIQ · press · retrieved 2026-11-04

Brand and model names identify the turbo and the vehicles it was fitted to; GAINS is not affiliated with their makers.