Supercharger pulley calculator: drive ratio and blower speed

Drive ratio = crank pulley ÷ blower pulley (× internal step-up for centrifugal units), and blower speed = engine rpm × drive ratio. Enter pulley sizes to check blower rpm against its limit and find the pulley for a target ratio, with an approximate boost estimate for positive-displacement blowers.

in
in
:1

1 for Roots and twin-screw; centrifugal superchargers have an internal gear step-up, often about 3-4:1 (see the maker's data).

rpm
rpm

From the supercharger maker. The default is illustrative.

:1

0 to skip the boost estimate (e.g. centrifugal units).

%
%
psi

Result

Drive ratio2.500 :1
Blower speed15,000 rpm
Share of blower maximum speed83 %
Blower pulley for the target ratio3.20 in
Approximate boost (positive displacement)9.8 psiapproximate, see assumptions
Air delivered ÷ air the engine swallows1.67 :1

Planning estimate from the formula below, not a measurement.

How it works

The formula, the method step by step, then a worked example.

ratio = (D_crank ÷ D_blower) × step-up;  N_blower = N_engine × ratio;  D_blower(target) = D_crank × step-up ÷ ratio;  density ratio ≈ (V_blower × N_blower × VE_b) ÷ (V_engine × N_engine ÷ 2 × VE_e);  boost ≈ (ratio − 1) × P_baro
  1. Belt speed is the same at both pulleys, so speed scales with the inverse of diameter.
  2. Centrifugal superchargers multiply that by their internal gear step-up.
  3. A positive-displacement blower moves a fixed volume per revolution; comparing what it delivers with what the engine swallows gives an approximate manifold density ratio, and from it boost.

Worked example

Inputs

Crank pulley diameter
8 in
Blower pulley diameter
3.2 in
Internal step-up ratio
1 :1
Engine speed
6000 rpm
Blower maximum rated speed
18000 rpm
Target drive ratio (for pulley size)
2.5 :1
Blower displacement per rev (L, positive displacement only)
2.3
Blower volumetric efficiency
90 %
Engine displacement (L)
6.2
Engine volumetric efficiency
100 %
Barometric pressure
14.7 psi

Result

Drive ratio2.500:1
Blower speed15000rpm
Share of blower maximum speed83%
Blower pulley for the target ratio3.20in
Approximate boost (positive displacement)9.8psi
Air delivered ÷ air the engine swallows1.67:1

Assumptions and limits

  • Belt slip ignored; use effective (pitch) diameters for ribbed belts if the maker lists them.
  • The boost figure is approximate: it ignores charge heating, bypass valve state and leakage beyond the blower VE you enter. Centrifugal boost depends on the compressor map instead.
  • Default blower speed limit and displacement are illustrative, not for a specific unit.

Related terms

Frequently asked

How do you calculate supercharger pulley ratio?

Divide the crank pulley diameter by the blower pulley diameter, and multiply by the internal step-up for centrifugal units. An 8 in crank and 3.2 in blower pulley give 2.5:1, so the blower turns 15,000 rpm at 6,000 engine rpm.

How much boost does a smaller supercharger pulley add?

On a positive-displacement blower, airflow rises roughly with blower speed, so a smaller pulley raises boost, but charge heating and leakage rise too. The estimate here is approximate; check blower speed against the maker's limit before changing pulleys.

What size pulley do I need for a target ratio?

Blower pulley = crank pulley × step-up ÷ target ratio. For an 8 in crank pulley and a 2.5:1 target on a Roots or twin-screw blower, that is 3.2 in. Check belt wrap and minimum pulley size with the belt maker.

Answers draw on the sources below.

Sources

  1. Automotive Handbook · Robert Bosch GmbH
  2. Internal Combustion Engine Fundamentals (2nd ed.), ch. 2: engine performance parameters (bmep, typical maximum and rated-power values) · J. B. Heywood, McGraw-Hill, 2018

Spot an error? Tell us.