1/4 mile calculator: ET, trap speed and horsepower (estimates)

Estimate quarter-mile ET and trap speed from power and weight, or power from a time slip, with the Hale relations: trap mph = 234 × (hp ÷ lb)^⅓ and ET = 5.825 × (lb ÷ hp)^⅓. All results are empirical estimates, not measurements.

lb
mph
hp

Engine (crank) power. Leave at 0 to estimate power from the time slip instead.

Result

Estimated power from trap speed (Hale)415 hp
Estimated power from ET (Hale)400 hp
Estimated power from trap speed (Fox)438 hp
Estimated power from ET (Fox)499 hp
ET a clean pass at this trap speed suggests11.85 seconds, Hale

Empirical estimate from published drag-racing relations, not a dyno measurement. Traction, gearing, aerodynamics, launch and weather all move the result.

Planning estimate from the formula below, not a measurement.

How it works

The formula, the method step by step, then a worked example.

trap mph = 234 × (P ÷ W)^⅓, ET = 5.825 × (W ÷ P)^⅓ (Hale);  so P = W × (mph ÷ 234)³ = W ÷ (ET ÷ 5.825)³, and ET × mph ≈ 5.825 × 234 = 1363;  Fox: 230 and 6.269
  1. Trap speed is set mainly by power-to-weight ratio, because the car is near its top acceleration by the end of the run.
  2. Published fits to drag-strip data give trap speed ∝ (power ÷ weight)^(1/3); invert it for power.
  3. ET depends more on launch and traction, so its estimate is less reliable than the trap-speed one.
  4. The same relations run forwards: from power and weight they predict ET and trap speed; multiplying the two Hale forms gives ET × trap speed ≈ 1,363, linking ET and trap speed directly.

Worked example

Inputs

Race weight with driver
3500 lb
Quarter-mile trap speed (from a time slip)
115 mph
Quarter-mile elapsed time (s)
12
Power, to predict ET and trap speed (optional)
0 hp

Result

Estimated power from trap speed (Hale)415hp
Estimated power from ET (Hale)400hp
Estimated power from trap speed (Fox)438hp
Estimated power from ET (Fox)499hp
ET a clean pass at this trap speed suggests11.85

Assumptions and limits

  • Weight in pounds including the driver; power is engine (flywheel) horsepower as the constants were fitted, though sources differ on this.
  • Typical street and strip cars on a quarter-mile track near sea level; very light, heavy, aerodynamically unusual or traction-limited cars fall outside the fit.
  • Labelled estimate: use a dyno or a logged acceleration run to measure power.

Related terms

Frequently asked

How do I calculate my quarter-mile ET?

A rough estimate from the Hale relation is ET = 5.825 × (weight ÷ power)^⅓, with weight in pounds including the driver. A 3,500 lb car with 400 hp at the crank works out to about 12.0 s and 113.6 mph. Launch, traction and gearing decide how close a real pass gets.

What ET should my trap speed run?

Multiplying the two Hale forms gives ET × trap mph ≈ 1,363, so a clean pass trapping 115 mph suggests about 11.9 s. A much slower ET than that usually means time lost at the launch, not missing power.

How accurate is trap speed for estimating horsepower?

It is a rough empirical estimate, not a measurement. Trap speed is less affected by launch and traction than ET, so it is the better of the two, but aerodynamics, gearing and weather all move it. Use a dyno to measure power.

What is the Hale formula?

Patrick Hale's relation: power = weight × (trap mph ÷ 234)³, with weight in pounds including the driver. Its ET form is power = weight ÷ (ET ÷ 5.825)³. Fox (1973) and Huntington published similar fits with slightly different constants.

Does trap speed give wheel or crank horsepower?

The constants were fitted to engine (flywheel) power figures, though sources differ. Treat the result as a rough engine power estimate and compare cars on the same basis.

Answers draw on the sources below.

Sources

  1. Quarter mile calculator (Huntington, Fox and Hale constants) · Omni Calculator · retrieved 2026-10-27
  2. On the physics of drag racing (G. Fox, 1973) · American Journal of Physics 41

Spot an error? Tell us.