Bosch, TE Connectivity and others (multi-source)

Fuel injector connectors: USCAR (EV6) and EV1 (Jetronic / Minitimer)

USCAR injector connectorEV6 connectorEV1 connectorJetronic connectorMinitimer connectorBosch injector plugMultec 2 connector

A USCAR connector, in fuel-injector talk, is the compact 2-pin plug also called EV6; the older Bosch-style plug is the EV1, also sold as Jetronic or Minitimer. The names describe the plug, not the injector's internals: Bosch sells its EV14 injector with Jetronic, Sumitomo or motorsport connectors. Mixing styles needs plug-in adapter pigtails or a re-pinned harness.Medium15

At a glance

EV1 aliasesJetronic, Minitimer, EV1the same Bosch-style plugSourced · medium1
USCAR aliasesUSCAR and EV6 name the same plugSourced · medium1
Contacts2per pluginjector coil supply and driverSourced67
Jetronic terminal
  • 2.8 mm blade system
  • Bosch lists TE JPT terminal 929939-3 (18-20 AWG, tin)
Sourced · medium6
USCAR housing and terminal part numbersNot confirmedWe found USCAR/EV6 kits only under retailer SKUs, with sellers naming different terminal makers (Yazaki in one kit, Delphi in another). No maker or distributor page tied a housing part number to the injector plug.Researched, unverified
Bosch EV14 options
  • Jetronic, Sumitomo or motorsport connectors
  • 12 Ω coil
  • 6-16.5 V supply
Sourced5
Ford EV1 era1986-95 5.0, 1996-2003 4.6 2VSourced · medium2
GM switch to USCARAbout 2005 on Gen IV car engines, about 2007 on trucksSourced · medium1

EV1, Jetronic, Minitimer, USCAR and EV6: what the names mean

Two injector plug styles cover most V8 and import swaps.

The older Bosch style goes by three names: Jetronic was first, then Minitimer, and EV1 today. The newer, more compact plug is called USCAR or EV6.Medium1

EV1, EV6 and EV14 are also Bosch injector generations, which is where the confusion starts. Bosch's own EV14 datasheet offers that injector with Jetronic, Sumitomo or motorsport plugs. Always check the plug on the injector you buy, not just its generation.Medium51

Injector plug styles compared

The table lists what each style is and where it appears.

Common 2-pin injector plug styles (OEM usage per press sources; verify against your injector)Medium12346
StyleAlso calledExamples of OEM useTerminal system
EV1Jetronic, Minitimer, Bosch styleGM TPI from about 1985, LS1 cars; Ford 1986-95 5.0, 1996-2003 4.6 2V2.8 mm blade (JPT) per Bosch Jetronic housing listing
USCAREV6GM Gen IV cars from about 2005, trucks from about 2007; Ford 1999-2001 Cobra, 2005-10 3V; Coyote port injectors; Mopar 5.7, 6.1, 6.4 HemiNot confirmed from a maker page
Multec 2Mini-Delphi (caption)Early GM Gen III truck 4.8, 5.3, 6.0Not confirmed from a maker page

OEM usage comes from enthusiast press (EngineLabs, OnAllCylinders), not OEM service data.

GM also used a third plug on early Gen III trucks; EngineLabs names it Multec 2 in its text and Mini-Delphi in a photo caption.Medium1

Jetronic (EV1) housing parts

Bosch sells the Jetronic 2-way housing by code number.

TE JPT injector plug

936139-1: 2 positions, 5 mm pitch, 2.8 mm receptacle, grey PBT, sealable, -40 to 125 °C

Sourced7
Bosch Jetronic 2-way Code 1 housing and accessories (distributor listing)Medium6
Part numberItemDetail
1 928 402 571Jetronic 2-way housing, Code 1, blackPA66 GF; 2.8 mm blade; axial connector seal plus single wire seals; lance lock, no secondary lock; -40 to 130 °C
929939-3JPT socket terminal (TE)18-20 AWG, tin
1 928 300 599Single wire sealBlue
1 928 300 600Single wire sealWhite
1 928 300 601Cavity plugBlanks an unused cavity
1 280 703 031Protective bootListed as a related part

The listing does not give the insulation range for each seal colour; check Bosch data before ordering.

A distributor listing for 1 928 402 571 gives the Code 1 black housing and the matching seals, cavity plug, boot and JPT terminal.Medium6

TE also lists a 2-position Junior Power Timer housing internally described as a JPT injector plug, 936139-1. TE does not say which injector it fits, so treat it as a related part rather than a confirmed EV1 match.Medium7

Adapter pigtails and re-pinning

When the harness and injectors use different plugs, a plug-in adapter pigtail is the usual fix.

EngineLabs gives the example of running older Jetronic injectors on a later EV6 harness, and notes that early GM truck injectors often need adapters because most aftermarket systems are built around EV6.Medium1

Avoid cutting in butt splices with mismatched wire. Extra resistance in the injector circuit changes how the injector opens, so use a made-for-purpose adapter or re-pin the harness with the correct housing.Medium1

Which engines use which plug

OnAllCylinders reports that Ford's EV1 era covered the 1986-95 5.0 and 1996-2003 4.6 2V, that EV6 arrived on the 1999-2001 Cobra and the 2005-10 3V, and that the 2011-on Coyote used EV14 injectors. Its Coyote guides list the port injectors as USCAR.Medium23

On Mopar, OnAllCylinders lists the Gen III 5.7, 6.1 and 6.4 Hemi injectors as USCAR/EV6. On GM, the LS1 car kept EV1, early Gen III trucks used the Multec 2 plug, and the later engines moved to USCAR.Medium41

Common mistakes

Ordering by injector generation alone is the main one.

Bosch builds the same EV14 body with different plugs, so read the connector field on the injector listing.5

Ignoring the housing code is another. Bosch sells the Jetronic 2-way housing by code number (1 928 402 571 is Code 1), so match the code on both halves of the joint.Medium6

CAD and drawings

We link to the maker's own downloads and do not rehost drawings, 3D models or specifications: the makers' terms grant no redistribution. Our cavity maps are drawn from the cavity numbers, never traced from these drawings.

Crimp and assembly quick card

Strip length929939: 4.7 ±0.3 mmSourced8
Crimp height
  • 929939 wire crimp height ±0.05 mm: FLK 0.5 mm² 1.18 (1.15 preferred*)
  • 0.75 mm² 1.271.18*
  • 1.0 mm² 1.361.20*
  • FLR wire same values. *TE's preferred values for the LV214-2 slow-bend test. Measurable crimp width 2.03 +0.20 mm
Sourced8
Pull-out force (minimum)

Per DIN EN 60352-2, measured without insulation crimp (no figure printed in 114-18050)

Sourced · mediumMedium8
Application spec

TE 114-18050 rev U (9 Sep 2025) for JPT 929939 (Jetronic EV1 terminal)

Applies to the Jetronic/EV1 side only. USCAR/EV6 terminal crimp data remains TBC.Sourced8

Assembly

  1. Slide the single-wire seal on first: 828904-1 for thinner insulation (e.g. 18 AWG TXL 1.88-2.13 mm), 828905-1 for thicker (e.g. GXL).8
  2. Strip 4.7 mm without bending or cutting strands and without damaging the insulation where the seal sits.8
  3. Crimp with hand tool 539635-1 and die set 539737-2 (or applicator 2151191 / 2266070); the conductor must stand 0.1-0.5 mm past the wire crimp and the insulation must not be in the wire crimp.8
  4. Seal empty cavities with dead-end plug 828922-X.8

Removal

  1. Release the contact from the housing with TE extraction tool 1-1579007-6.8

Summarised in our own words from the maker's application specifications and instruction sheets cited above. Disconnect the battery before working on a vehicle harness. A crimp is only as good as its pull test: check samples with your tool and wire before building a loom. Choosing a crimp tool →

Kit parts for this family

ItemPart numberDescriptionWireQtySource
Terminal929939-x (strip) / 929940-x (loose)JPT receptacle for single-wire seal, 0.5-1.0 mm²0.5-1.0 mm²1 per wire8
Seal828904-1Single-wire seal for thinner insulation (e.g. 0.5-1.0 mm² FLR, 18-20 AWG TXL)1.58-2.13 mm OD (per TE table rows)1 per wire8
Seal828905-1Single-wire seal for thicker insulation (FLK, GXL)2.06-3.00 mm OD (per TE table rows)1 per wire8
Seal1928300599 / 1928300600Bosch wire seals (blue / white) listed beside the Jetronic 1 928 402 571 housingDistributor shows them as related parts; insulation ranges and kit fit not confirmed.All1 per wireUnverifiedLow6
Cavity plug828922-XDead-end plug for unused cavitiesSuffix not given in the spec.Allper unused cavity8
Cavity plug1928300601Bosch cavity plug, transparent (related item)Not published in the documents we could read; TBC.Allper unused cavityUnverifiedLow6
Boot1280703031Bosch 2-way protective rubber boot (related item)Not published in the documents we could read; TBC.All1UnverifiedLow6
Crimp tool539635-1 + die 539737-2Hand tool and die for 9299390.5-1.0 mm²18
Removal tool1-1579007-6JPT extraction toolAll18

Where it's used

Our harness designs

Not used in our current harness designs.

Sensors that mate with it

No sensor in our sensor library lists this connector yet.

Factory (OEM) use

Frequently asked

Is a USCAR connector the same as EV6?

Yes, for injectors the two names describe the same compact 2-pin plug, and press guides write it as USCAR/EV6. The older Bosch-style plug is the separate EV1 style, also called Jetronic or Minitimer. EV6 is also a Bosch injector generation, so check the plug itself rather than the injector's model name.Medium15

What is the difference between EV1 and EV6 injector connectors?

They are different plugs and do not mate. EV1, also sold as Jetronic or Minitimer, is the older and larger Bosch-style plug used on GM TPI and LS1 cars and Ford engines up to about 2003. USCAR, or EV6, is the compact plug that replaced it on most newer domestic V8s. Moving between them needs adapters or a re-pinned harness.Medium12

What connector does a Bosch EV14 injector use?

It depends on the variant. Bosch's EV14 datasheet lists Jetronic, Sumitomo and motorsport connectors on the same 12 Ω injector family, and asks buyers to check before ordering. Confirm the connector field on the exact part number you buy, and plan adapters if it differs from your harness.5

Do I need injector adapters for an LS swap?

Only if your injectors and harness use different plugs. LS1 car injectors use EV1, early Gen III truck injectors use the Multec 2 plug, and later truck and Gen IV injectors use USCAR/EV6. EngineLabs notes that early truck injectors often need adapters because most aftermarket systems are built for EV6 plugs.Medium1

Can I splice injector wires instead of using adapters?

You can, but it is the riskier route. EngineLabs warns that homemade butt-splice jobs with mismatched wire add resistance that can change injector behaviour, and recommends purpose-built adapters. If you re-pin instead, use the correct housing, terminals and wire seals for the plug style so the joint stays sealed.Medium16

Keep going

Related

Sources

  1. Injector specs: GM fuel injector identification and cross reference · EngineLabs · press · retrieved 2026-10-27
  2. Understanding Ford fuel injectors · OnAllCylinders · press · retrieved 2026-10-27
  3. 2011-14 Ford Mustang GT 5.0L first-gen Coyote engine spec guide · OnAllCylinders · press · retrieved 2026-10-27
  4. Mopar Gen III 5.7L Hemi engine guide · OnAllCylinders · press · retrieved 2026-10-27
  5. Injection Valve EV 14 datasheet · Bosch Motorsport (copy hosted by Lingenfelter Performance Engineering) · vendor-doc · retrieved 2026-10-27
  6. 1928402571 Bosch Jetronic 2-way connector, Code 1, black · Chief Enterprises (distributor) · vendor-doc · retrieved 2026-10-27
  7. 936139-1 Junior Power Timer 2-position housing (JPT injector plug) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  8. Application Specification 114-18050 rev U (9 Sep 2025): Junior Power Timer contact system · TE Connectivity · vendor-doc · retrieved 2026-10-28

Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.