Garrett GTX2867R Gen II compressor map

GTX Gen IIGTX28 frame50 mm inducer67 mm exducerModelled estimate

Map data from Garrett Motion, retrieved 2026-10-25.

The Garrett GTX2867R Gen II compressor peaks at 72% efficiency around 29 lb/min and a pressure ratio of 2.2. Its map reaches a pressure ratio of about 3.9, and at a pressure ratio of 2 it flows from about 12 lb/min (surge) to 42 lb/min (choke side).

Peak efficiency
72%
island 19–39 lb/min, PR 1.6–2.8
Surge line
6–32
lb/min, from PR 1.3 to 3.9
Choke side, max flow
49
lb/min (0.368 kg/s)
Pressure-ratio reach
3.88
about 42 psi boost at sea level, before losses
Map width at PR 2
3.6×
choke flow ÷ surge flow
Outlet temp at peak island
262 °F
from 77 °F inlet, PR 2.2, 72% efficiency

Flow range

0306090120

Light band: usable flow at a pressure ratio of 2 (surge to choke side). Solid band: the 72% island. Scale 0–120 lb/min. We show figures derived from the map, not the map itself. See the maker's compressor map for the full islands and speed lines.

Surge and choke

Surge is the left-hand limit: too little flow for the pressure ratio, so air reverses through the wheel. On this map the surge line runs from about 6.4 lb/min (0.048 kg/s) at a pressure ratio of 1.3 to 32.4 lb/min (0.245 kg/s) at 3.9. Keep the full-load operating line to the right of it, with margin for transients.

Choke is the right-hand limit, where efficiency falls away and the wheel can't pass more air. The digitised choke side spans 17.5 lb/min (0.132 kg/s) to 48.7 lb/min (0.368 kg/s) across pressure ratios 1.2–3.9. It is the lowest efficiency contour the maker draws (61%), not a measured choke line.

Shaft-speed lines on the map run from 65k to 165k rpm.

Engines it suits

We ran every engine preset in the turbo matcher at three boost levels and ranked all 20 maps for each. These are the engines where this compressor came out in the top three and the whole operating line stayed on the map, with no surge or choke. Modelled estimate

30 psi, single turbo

EngineRankEfficient fromLowest surge marginPeak PR
Duratec ST 2.5T (5-cyl) · Ford/Volvo2 of 205,000 rpm7%3.25
1JZ-GTE (twin / single VVT-i) · Toyota2 of 205,000 rpm8%3.25

Assumptions (the matcher's defaults): stock torque-curve VE shape scaled to 92% peak, full boost from 3,500 rpm to redline, 120 °F charge after the intercooler, 77 °F ambient at sea level, 1.5 psi charge-side and 0.5 psi inlet losses, gasoline. A compressor map says nothing about spool or transient response; the turbine housing decides much of that. The interactive turbo matcher opens once map review is complete.

Turbine housings

The maker's turbine flow chart for this frame lists 4 housings. Highest corrected gas flow digitised for each:

HousingMax corrected flow (lb/min)At expansion ratio
76 trim 0.86 A/R19.62.50
76 trim 0.72 A/R17.33.00
76 trim 0.64 A/R16.42.75
76 trim 0.57 A/R14.63.25

Expansion ratio and flow as labelled on the maker's chart. See A/R ratio for how housing size trades spool against top-end flow.

Maker's published spec

Family
GTX Gen II
Bearing
8mm dual ceramic ball bearing
Compressor wheel
50 mm inducer, 67 mm exducer
Turbine housing A/R
0.57, 0.64, 0.72, 0.86
Maker's engine size range
1.4L-2.5L

Compare

Related

How these numbers are made

Method
manual reading from the maker's published map image at 1714x2048 px, assisted by row-wise dark-pixel crossing scans on a calibrated pixel grid (axis ticks located to +/-1 px)
Accuracy
about +/-1.5% of axis span on surge, left/lower island branches and speed lines; about +/-3% of axis span on the near-choke right-hand island sides (drawn dashed by Garrett and overlapped by labels)
Flow correction
302.8 K, 96.18 kPa. Not printed on this map image (Garrett's current web maps carry no correction footnote and none was found on garrettmotion.com). Values are Garrett's long-standing convention printed on its legacy GT-series compressor maps: 545 degR (85 degF) and 13.95 psia. Treat as assumed, not maker-stated for this map.
Pressure-ratio basis
Not stated on the maker's map

Every figure on this page is a modelled estimate derived from that digitisation. It is not a flow-bench or dyno result and makes no power claim.

Sources

Garrett and model names are trademarks of their owners and identify the part only. No affiliation or endorsement is implied.