Garrett GTX3582R Gen II compressor map
Map data from Garrett Motion, retrieved 2026-10-25.
The Garrett GTX3582R Gen II compressor peaks at 76% efficiency around 40 lb/min and a pressure ratio of 2.1. Its map reaches a pressure ratio of about 4.1, and at a pressure ratio of 2 it flows from about 17 lb/min (surge) to 68 lb/min (choke side).
Flow range
Light band: usable flow at a pressure ratio of 2 (surge to choke side). Solid band: the 76% island. Scale 0–120 lb/min. We show figures derived from the map, not the map itself. See the maker's compressor map for the full islands and speed lines.
The 75% efficiency island is not resolved on this map.
Surge and choke
Surge is the left-hand limit: too little flow for the pressure ratio, so air reverses through the wheel. On this map the surge line runs from about 8.0 lb/min (0.061 kg/s) at a pressure ratio of 1.3 to 39.4 lb/min (0.298 kg/s) at 4.1. Keep the full-load operating line to the right of it, with margin for transients.
Choke is the right-hand limit, where efficiency falls away and the wheel can't pass more air. The digitised choke side spans 28.0 lb/min (0.212 kg/s) to 82.1 lb/min (0.620 kg/s) across pressure ratios 1.1–4.1. It is the lowest efficiency contour the maker draws (60%), not a measured choke line.
Shaft-speed lines on the map run from 50k to 130k rpm.
Engines it suits
We ran every engine preset in the turbo matcher at three boost levels and ranked all 20 maps for each. These are the engines where this compressor came out in the top three and the whole operating line stayed on the map, with no surge or choke. Modelled estimate
30 psi, single turbo
| Engine | Rank | Efficient from | Lowest surge margin | Peak PR |
|---|---|---|---|---|
| 1UZ-FE / 3UZ-FE V8 · Toyota | 3 of 20 | — | 7% | 3.25 |
| Lambda 3.8 MPI · Hyundai | 3 of 20 | — | 0% | 3.25 |
Assumptions (the matcher's defaults): stock torque-curve VE shape scaled to 92% peak, full boost from 3,500 rpm to redline, 120 °F charge after the intercooler, 77 °F ambient at sea level, 1.5 psi charge-side and 0.5 psi inlet losses, gasoline. A compressor map says nothing about spool or transient response; the turbine housing decides much of that. The interactive turbo matcher opens once map review is complete.
Turbine housings
The maker's turbine flow chart for this frame lists 6 housings. Highest corrected gas flow digitised for each:
| Housing | Max corrected flow (lb/min) | At expansion ratio |
|---|---|---|
| 84 trim 1.06 A/R | 31.7 | 2.75 |
| 84 trim 1.01 A/R | 29.8 | 3.50 |
| 84 trim 0.83 A/R | 27.6 | 3.50 |
| 84 trim 0.82 A/R | 26.9 | 2.75 |
| 84 trim 0.63 A/R | 24.3 | 3.50 |
| 84 trim 0.61 A/R | 22.8 | 3.50 |
Expansion ratio and flow as labelled on the maker's chart. See A/R ratio for how housing size trades spool against top-end flow.
Maker's published spec
- Family
- GTX Gen II
- Bearing
- 8mm dual ceramic ball bearing
- Compressor wheel
- 66 mm inducer, 82 mm exducer
- Turbine housing A/R
- 0.61, 0.63, 0.82, 0.83, 1.01, 1.06
- Maker's engine size range
- 2.0L-4.5L
Compare
Related
How these numbers are made
- Digitised from
- Garrett GTX3582R Gen II compressor map (lb/min and kg/s axes), linked from the GTX3582R Gen II product page https://www.garrettmotion.com/racing-and-performance/performance-catalog/turbo/gtx3582r-gen-ii/ (Garrett Motion, retrieved 2026-10-25)
- Method
- manual reading from the maker's published map image at 1714x2048 px (contours traced by eye on a calibrated pixel grid; this map's dense, closely labelled contours were not scan-assisted)
- Accuracy
- about +/-3% of axis span overall; up to +/-5% near the low-flow island tips where contours converge; 73-76% label-to-contour assignment uncertain (see reference.note)
- Flow correction
- 302.8 K, 96.18 kPa. Not printed on this map image (Garrett's current web maps carry no correction footnote and none was found on garrettmotion.com). Values are Garrett's long-standing convention printed on its legacy GT-series compressor maps: 545 degR (85 degF) and 13.95 psia. Treat as assumed, not maker-stated for this map. Digitizing caveat: on this image the 73-76% labels sit very close together and only six closed inner contours could be separated; they are assigned 76/74/73/72/71/70 from label placement, and no separate 75% contour is included. The 60/65/68% islands are open to the top (max-speed) boundary on Garrett's chart and are closed along that boundary here.
- Pressure-ratio basis
- Not stated on the maker's map
Every figure on this page is a modelled estimate derived from that digitisation. It is not a flow-bench or dyno result and makes no power claim.
Sources
- Garrett Motion: compressor map retrieved 2026-10-25
- Garrett: product page retrieved 2026-10-25
Garrett and model names are trademarks of their owners and identify the part only. No affiliation or endorsement is implied.

