BorgWarner EFR 8374 compressor map

EFR62 mm inducer84 mm exducerModelled estimate

Map data from BorgWarner Inc., retrieved 2026-10-25.

The BorgWarner EFR 8374 compressor peaks at 77% efficiency around 47 lb/min and a pressure ratio of 2.6. Its map reaches a pressure ratio of about 4.8, and at a pressure ratio of 2 it flows from about 20 lb/min (surge) to 79 lb/min (choke side).

Peak efficiency
77%
island 39–55 lb/min, PR 2.1–3.1
Surge line
14–54
lb/min, from PR 1.7 to 4.8
Choke side, max flow
79
lb/min (0.598 kg/s)
Pressure-ratio reach
4.78
about 56 psi boost at sea level, before losses
Map width at PR 2
4.0×
choke flow ÷ surge flow
Outlet temp at peak island
296 °F
from 77 °F inlet, PR 2.6, 77% efficiency

Flow range

0306090120

Light band: usable flow at a pressure ratio of 2 (surge to choke side). Solid band: the 77% island. Scale 0–120 lb/min. We show figures derived from the map, not the map itself. See the maker's compressor map for the full islands and speed lines.

Surge and choke

Surge is the left-hand limit: too little flow for the pressure ratio, so air reverses through the wheel. On this map the surge line runs from about 14.3 lb/min (0.108 kg/s) at a pressure ratio of 1.7 to 54.1 lb/min (0.409 kg/s) at 4.8. Keep the full-load operating line to the right of it, with margin for transients.

Choke is the right-hand limit, where efficiency falls away and the wheel can't pass more air. The digitised choke side spans 54.9 lb/min (0.415 kg/s) to 79.0 lb/min (0.598 kg/s) across pressure ratios 1.3–4.8. It is the lowest efficiency contour the maker draws (60%), not a measured choke line.

Shaft-speed lines on the map run from 64k to 128k rpm.

Engines it suits

We ran every engine preset in the turbo matcher at three boost levels and ranked all 20 maps for each. These are the engines where this compressor came out in the top three and the whole operating line stayed on the map, with no surge or choke. Modelled estimate

22 psi, single turbo

EngineRankEfficient fromLowest surge marginPeak PR
4.6 2V · Ford1 of 203,500 rpm32%2.69
Lambda 3.8 MPI · Hyundai2 of 204,000 rpm5%2.69
5.0 / 302 + 5.8 / 351W · Ford3 of 203,000 rpm50%2.69
Barra 4.0 NA · Ford AU3 of 203,500 rpm20%2.69
Barra 4.0 Turbo (XR6T / F6) · Ford AU3 of 203,500 rpm20%2.69
4.6 3V (VCT) · Ford3 of 203,500 rpm28%2.69

30 psi, single turbo

EngineRankEfficient fromLowest surge marginPeak PR
Barra 4.0 NA · Ford AU1 of 203,500 rpm5%3.25
Barra 4.0 Turbo (XR6T / F6) · Ford AU1 of 203,500 rpm9%3.25
5.0 / 302 + 5.8 / 351W · Ford2 of 203,000 rpm31%3.25

Assumptions (the matcher's defaults): stock torque-curve VE shape scaled to 92% peak, full boost from 3,500 rpm to redline, 120 °F charge after the intercooler, 77 °F ambient at sea level, 1.5 psi charge-side and 0.5 psi inlet losses, gasoline. A compressor map says nothing about spool or transient response; the turbine housing decides much of that. The interactive turbo matcher opens once map review is complete.

Turbine housings

The maker's turbine flow chart for this frame lists 4 housings. Highest corrected gas flow digitised for each:

HousingMax corrected flow (corrected flow parameter)At expansion ratio
0.83 A/R T3 (chart: 74mm 0.83a/r)0.03.00
0.92 A/R T4 twin (chart: 74mm 0.92a/r)0.03.00
1.05 A/R T4 twin (chart: 74mm 1.05a/r)0.03.00
1.45 A/R T4 twin (chart: 74mm 1.45a/r)0.03.00

Expansion ratio and flow as labelled on the maker's chart. See A/R ratio for how housing size trades spool against top-end flow.

Maker's published spec

Family
EFR
Bearing
dual ceramic ball bearing, metal cage
Compressor wheel
62 mm inducer, 84 mm exducer
Turbine housing A/R
0.83 (-B T3), 0.92 (-C T4 twin), 1.05 (-D T4 twin, no IWG), 1.45 (-H T4 twin, no IWG)

Compare

Related

How these numbers are made

Digitised from
EFR 8374 datasheet (8374-B/C/D), Compressor Map (applicable to all 8374 units) (BorgWarner Inc., retrieved 2026-10-25)
Method
manual reading from the maker's published map image at vector resolution (the datasheet PDF embeds the map as vector paths; curves were extracted from the PDF geometry, calibrated against the gridlines, contour fragments identified and joined by hand, open contours closed along the surge line / top speed line, then resampled)
Accuracy
+/-0.3 lb/min and +/-0.01 PR on traced lines (vector source); island polygons are resampled to ~20 points and contours that the map leaves open (cut by label gaps, the surge line or the max-speed line) were closed along the map boundary or by short chords, so island edges near those closures are approximate (+/-1 lb/min).
Flow correction
298.2 K, 100.00 kPa. The EFR datasheet map does not state its correction reference. Value used is BorgWarner's own documented convention: the BorgWarner MatchBot sizing tool (borgwarner.com/matchbot, bot.js) corrects compressor flow as m*sqrt((T+460)/537 R)/(P_kPa/100), i.e. 537 R (77 F, ~298 K) and 100 kPa. Flow axis is 'Compressor Flow (lb/min)'. The PR basis is not stated on the datasheet (BorgWarner's EFR Technical Training Book maps label PR as p2t/p1t, total-to-total). On this map the 64 krpm speed line forms the lower boundary; contours that end on it were closed along that line.
Pressure-ratio basis
Not stated on the maker's map

Every figure on this page is a modelled estimate derived from that digitisation. It is not a flow-bench or dyno result and makes no power claim.

Sources

BorgWarner and model names are trademarks of their owners and identify the part only. No affiliation or endorsement is implied.