BorgWarner EFR 9180 compressor map
Map data from BorgWarner Inc., retrieved 2026-10-25.
The BorgWarner EFR 9180 compressor peaks at 77% efficiency around 51 lb/min and a pressure ratio of 2.5. Its map reaches a pressure ratio of about 4.9, and at a pressure ratio of 2 it flows from about 24 lb/min (surge) to 95 lb/min (choke side).
Flow range
Light band: usable flow at a pressure ratio of 2 (surge to choke side). Solid band: the 77% island. Scale 0–120 lb/min. We show figures derived from the map, not the map itself. See the maker's compressor map for the full islands and speed lines.
Surge and choke
Surge is the left-hand limit: too little flow for the pressure ratio, so air reverses through the wheel. On this map the surge line runs from about 7.1 lb/min (0.054 kg/s) at a pressure ratio of 1.2 to 63.4 lb/min (0.479 kg/s) at 4.9. Keep the full-load operating line to the right of it, with margin for transients.
Choke is the right-hand limit, where efficiency falls away and the wheel can't pass more air. The digitised choke side spans 63.1 lb/min (0.477 kg/s) to 95.1 lb/min (0.719 kg/s) across pressure ratios 1.3–4.9. It is the lowest efficiency contour the maker draws (60%), not a measured choke line.
Shaft-speed lines on the map run from 35k to 116k rpm.
Engines it suits
We ran every engine preset in the turbo matcher at three boost levels and ranked all 20 maps for each. These are the engines where this compressor came out in the top three and the whole operating line stayed on the map, with no surge or choke. Modelled estimate
22 psi, single turbo
| Engine | Rank | Efficient from | Lowest surge margin | Peak PR |
|---|---|---|---|---|
| 5.2 / 5.9 Magnum · Chrysler | 1 of 20 | 3,000 rpm | 36% | 2.69 |
| 4.6 2V · Ford | 2 of 20 | 3,500 rpm | 0% | 2.69 |
| SBC 350 (L98 TPI / L31 Vortec) · GM | 3 of 20 | 3,000 rpm | 36% | 2.69 |
30 psi, single turbo
| Engine | Rank | Efficient from | Lowest surge margin | Peak PR |
|---|---|---|---|---|
| 5.0 / 302 + 5.8 / 351W · Ford | 1 of 20 | 3,500 rpm | 7% | 3.25 |
| L83 5.3 / L86 6.2 (Gen V truck) · GM | 2 of 20 | 3,500 rpm | 6% | 3.25 |
| 5.2 / 5.9 Magnum · Chrysler | 3 of 20 | 3,000 rpm | 25% | 3.25 |
| SBC 350 (L98 TPI / L31 Vortec) · GM | 3 of 20 | 3,000 rpm | 25% | 3.25 |
| 6.0 LQ4 / LQ9 / LY6 / L96 (truck) · GM | 3 of 20 | 3,000 rpm | 21% | 3.25 |
| L84 5.3 / L87 6.2 (Gen V with DFM) · GM | 3 of 20 | 3,500 rpm | 6% | 3.25 |
Assumptions (the matcher's defaults): stock torque-curve VE shape scaled to 92% peak, full boost from 3,500 rpm to redline, 120 °F charge after the intercooler, 77 °F ambient at sea level, 1.5 psi charge-side and 0.5 psi inlet losses, gasoline. A compressor map says nothing about spool or transient response; the turbine housing decides much of that. The interactive turbo matcher opens once map review is complete.
Turbine housings
The maker's turbine flow chart for this frame lists 4 housings. Highest corrected gas flow digitised for each:
| Housing | Max corrected flow (corrected flow parameter) | At expansion ratio |
|---|---|---|
| 0.83 A/R T3 (chart: 80mm 0.83a/r) | 0.0 | 3.00 |
| 0.92 A/R T4 twin (chart label: 80mm 0.91a/r, shares the 0.83 curve) | 0.0 | 3.00 |
| 1.05 A/R T4 twin (chart: 80mm 1.05a/r) | 0.0 | 3.00 |
| 1.45 A/R T4 twin (chart: 80mm 1.45a/r) | 0.1 | 3.00 |
Expansion ratio and flow as labelled on the maker's chart. See A/R ratio for how housing size trades spool against top-end flow.
Maker's published spec
- Family
- EFR
- Bearing
- dual ceramic ball bearing, metal cage
- Compressor wheel
- 68 mm inducer, 91 mm exducer
- Turbine housing A/R
- 0.83 (-B T3), 0.92 (-C T4 twin), 1.05 (-D T4 twin, no IWG), 1.45 (-H T4 twin, no IWG)
Compare
Related
How these numbers are made
- Digitised from
- EFR 9180-B / 9180-C / 9180-D datasheet, Compressor Map (applicable to all 9174 and 9180 units) (BorgWarner Inc., retrieved 2026-10-25)
- Method
- manual reading from the maker's published map image at vector resolution (the datasheet PDF embeds the map as vector paths; curves were extracted from the PDF geometry, calibrated against the gridlines, contour fragments identified and joined by hand, open contours closed along the surge line / top speed line, then resampled)
- Accuracy
- +/-0.5 lb/min and +/-0.015 PR on traced lines. This datasheet stores the map lines as filled outlines, so centerlines were reconstructed from the outlines (+/-0.1 lb/min); the 0.76 island is the convex hull of its outline; islands are resampled to ~22 points and contours left open by the map were closed along the surge line / max-speed line or by short chords (+/-1-2 lb/min near those closures).
- Flow correction
- 298.2 K, 100.00 kPa. The EFR datasheet map does not state its correction reference. Value used is BorgWarner's own documented convention: the BorgWarner MatchBot sizing tool (borgwarner.com/matchbot, bot.js) corrects compressor flow as m*sqrt((T+460)/537 R)/(P_kPa/100), i.e. 537 R (77 F, ~298 K) and 100 kPa. Flow axis is 'Compressor Flow (lb/min)'. The PR basis is not stated on the datasheet (BorgWarner's EFR Technical Training Book maps label PR as p2t/p1t, total-to-total).
- Pressure-ratio basis
- Not stated on the maker's map
Every figure on this page is a modelled estimate derived from that digitisation. It is not a flow-bench or dyno result and makes no power claim.
Sources
- BorgWarner Inc.: compressor map retrieved 2026-10-25
- BorgWarner: product page retrieved 2026-10-25
BorgWarner and model names are trademarks of their owners and identify the part only. No affiliation or endorsement is implied.

