BorgWarner S366 SX-E compressor map

AirWerks S300SX-ES300 frameModelled estimate

Map data from BorgWarner Inc., retrieved 2026-10-25.

The BorgWarner S366 SX-E compressor peaks at 77% efficiency around 45 lb/min and a pressure ratio of 2.2. Its map reaches a pressure ratio of about 4.9, and at a pressure ratio of 2 it flows from about 20 lb/min (surge) to 76 lb/min (choke side).

Peak efficiency
77%
island 33–58 lb/min, PR 1.6–2.8
Surge line
9–63
lb/min, from PR 1.4 to 4.9
Choke side, max flow
87
lb/min (0.654 kg/s)
Pressure-ratio reach
4.91
about 57 psi boost at sea level, before losses
Map width at PR 2
3.9×
choke flow ÷ surge flow
Outlet temp at peak island
254 °F
from 77 °F inlet, PR 2.2, 77% efficiency

Flow range

0306090120

Light band: usable flow at a pressure ratio of 2 (surge to choke side). Solid band: the 77% island. Scale 0–120 lb/min. We show figures derived from the map, not the map itself. See the maker's compressor map for the full islands and speed lines.

Surge and choke

Surge is the left-hand limit: too little flow for the pressure ratio, so air reverses through the wheel. On this map the surge line runs from about 9.3 lb/min (0.070 kg/s) at a pressure ratio of 1.4 to 62.7 lb/min (0.474 kg/s) at 4.9. Keep the full-load operating line to the right of it, with margin for transients.

Choke is the right-hand limit, where efficiency falls away and the wheel can't pass more air. The digitised choke side spans 40.5 lb/min (0.306 kg/s) to 86.6 lb/min (0.654 kg/s) across pressure ratios 1.3–4.6. It is the lowest efficiency contour the maker draws (56%), not a measured choke line.

Shaft-speed lines on the map run from 48k to 117k rpm.

Engines it suits

We ran every engine preset in the turbo matcher at three boost levels and ranked all 20 maps for each. These are the engines where this compressor came out in the top three and the whole operating line stayed on the map, with no surge or choke. Modelled estimate

15 psi, single turbo

EngineRankEfficient fromLowest surge marginPeak PR
SBC 350 (L98 TPI / L31 Vortec) · GM1 of 203,000 rpm92%2.20
6.0 LQ4 / LQ9 / LY6 / L96 (truck) · GM1 of 203,000 rpm93%2.20
L84 5.3 / L87 6.2 (Gen V with DFM) · GM1 of 203,500 rpm69%2.20
L83 5.3 / L86 6.2 (Gen V truck) · GM1 of 203,500 rpm69%2.20
Coyote Gen 2 · Ford1 of 203,500 rpm58%2.20
VR38DETT (R35 GT-R) · Nissan1 of 204,500 rpm26%2.20
Coyote Gen 4 · Ford1 of 203,500 rpm53%2.20
S65 4.0 V8 (E9x M3) · BMW1 of 204,000 rpm29%2.20

22 psi, single turbo

EngineRankEfficient fromLowest surge marginPeak PR
4.6 3V (VCT) · Ford1 of 203,500 rpm28%2.69
1UZ-FE / 3UZ-FE V8 · Toyota1 of 204,000 rpm11%2.69
VR38DETT (R35 GT-R) · Nissan1 of 204,500 rpm9%2.69
Lambda 3.8 MPI · Hyundai1 of 204,500 rpm4%2.69
S65 4.0 V8 (E9x M3) · BMW1 of 204,000 rpm15%2.69
5.2 / 5.9 Magnum · Chrysler2 of 203,000 rpm77%2.69
4.6 2V · Ford3 of 203,500 rpm31%2.69
L83 5.3 / L86 6.2 (Gen V truck) · GM3 of 203,500 rpm50%2.69

30 psi, single turbo

EngineRankEfficient fromLowest surge marginPeak PR
SBC 350 (L98 TPI / L31 Vortec) · GM1 of 203,000 rpm58%3.25
4.6 2V · Ford1 of 203,500 rpm16%3.25
4.6 3V (VCT) · Ford1 of 203,500 rpm13%3.25
Barra 4.0 NA · Ford AU2 of 204,000 rpm7%3.25
Barra 4.0 Turbo (XR6T / F6) · Ford AU2 of 204,000 rpm12%3.25
5.0 / 302 + 5.8 / 351W · Ford3 of 203,500 rpm34%3.25

Assumptions (the matcher's defaults): stock torque-curve VE shape scaled to 92% peak, full boost from 3,500 rpm to redline, 120 °F charge after the intercooler, 77 °F ambient at sea level, 1.5 psi charge-side and 0.5 psi inlet losses, gasoline. A compressor map says nothing about spool or transient response; the turbine housing decides much of that. The interactive turbo matcher opens once map review is complete.

Compare

Related

How these numbers are made

Method
manual reading from the maker's published map image at 934x655 px (contours traced with a pixel line-follower seeded and checked by hand against zoomed, grid-overlaid renders; levels assigned by contour nesting order; open contours closed along the surge line, the 116,968 rpm line / choke and the 230 m/s bottom speed line; resampled to 22 points)
Accuracy
0.66-0.77 islands: +/-0.4 lb/min, +/-0.02 PR (about +/-4 px). 0.56-0.64 islands: the right and lower flanks are bunched and partly obscured by speed-line ends and labels; their lower branches below about PR 2.0 (0.56-0.60) are extrapolated, so allow +/-1.5 lb/min, +/-0.05 PR there. Surge and choke lines: +/-0.5 lb/min. Only the 230 m/s and 116,968 rpm speed lines are included.
Flow correction
298.2 K, 100.00 kPa. The map image states only 'Compressor Flow (lb/min)' and 'Pressure Ratio'; no correction reference or PR basis is printed. Value used is BorgWarner's own documented convention from the BorgWarner MatchBot sizing tool that publishes this map (bot.js corrects compressor flow as m*sqrt((T+460)/537 R)/(P_kPa/100): 537 R ~ 298 K, 100 kPa). Speed lines on the map are labelled in compressor tip speed (m/s) except the top line (116,968 rpm); the 230 m/s line here is converted to rpm using the 91.44 mm exducer from the S300SX-E datasheet.
Pressure-ratio basis
Not stated on the maker's map

Every figure on this page is a modelled estimate derived from that digitisation. It is not a flow-bench or dyno result and makes no power claim.

Sources

BorgWarner and model names are trademarks of their owners and identify the part only. No affiliation or endorsement is implied.