Garrett G42-1200 compressor map
Map data from Garrett Motion, retrieved 2026-10-25.
The Garrett G42-1200 compressor peaks at 79% efficiency around 70 lb/min and a pressure ratio of 2.5. Its map reaches a pressure ratio of about 4.2, and at a pressure ratio of 2 it flows from about 26 lb/min (surge) to 104 lb/min (choke side).
Flow range
Light band: usable flow at a pressure ratio of 2 (surge to choke side). Solid band: the 79% island. Scale 0–120 lb/min. We show figures derived from the map, not the map itself. See the maker's compressor map for the full islands and speed lines.
Surge and choke
Surge is the left-hand limit: too little flow for the pressure ratio, so air reverses through the wheel. On this map the surge line runs from about 13.0 lb/min (0.098 kg/s) at a pressure ratio of 1.3 to 76.8 lb/min (0.581 kg/s) at 4.2. Keep the full-load operating line to the right of it, with margin for transients.
Choke is the right-hand limit, where efficiency falls away and the wheel can't pass more air. The digitised choke side spans 38.4 lb/min (0.290 kg/s) to 112.6 lb/min (0.851 kg/s) across pressure ratios 1.1–4.2. It is the lowest efficiency contour the maker draws (60%), not a measured choke line.
Shaft-speed lines on the map run from 44k to 118k rpm.
Engines it suits
We ran every engine preset in the turbo matcher at three boost levels and ranked all 20 maps for each. These are the engines where this compressor came out in the top three and the whole operating line stayed on the map, with no surge or choke. Modelled estimate
15 psi, single turbo
| Engine | Rank | Efficient from | Lowest surge margin | Peak PR |
|---|---|---|---|---|
| 7.3 Godzilla · Ford | 1 of 20 | 3,500 rpm | 41% | 2.20 |
| LS7 · GM | 1 of 20 | 3,500 rpm | 30% | 2.20 |
| LT4 (supercharged) · GM | 1 of 20 | 4,000 rpm | 15% | 2.20 |
| M156 6.2 · Mercedes | 1 of 20 | 4,000 rpm | 14% | 2.20 |
| 6.1 / 6.4 392 Hemi · Chrysler | 1 of 20 | 3,500 rpm | 22% | 2.20 |
| LS9 (supercharged) · GM | 1 of 20 | 4,000 rpm | 12% | 2.20 |
| LS3 / L99 · GM | 1 of 20 | 4,000 rpm | 16% | 2.20 |
| LT1 (Gen V) · GM | 1 of 20 | 4,000 rpm | 16% | 2.20 |
22 psi, single turbo
| Engine | Rank | Efficient from | Lowest surge margin | Peak PR |
|---|---|---|---|---|
| 7.3 Godzilla · Ford | 1 of 20 | 3,500 rpm | 39% | 2.69 |
| LT4 (supercharged) · GM | 1 of 20 | 3,500 rpm | 14% | 2.69 |
| M156 6.2 · Mercedes | 1 of 20 | 4,000 rpm | 12% | 2.69 |
| LS2 · GM | 1 of 20 | 4,000 rpm | 12% | 2.69 |
| LS3 / L99 · GM | 1 of 20 | 4,000 rpm | 14% | 2.69 |
| LT1 (Gen V) · GM | 1 of 20 | 4,000 rpm | 14% | 2.69 |
| 6.1 / 6.4 392 Hemi · Chrysler | 1 of 20 | 3,500 rpm | 20% | 2.69 |
| LS9 (supercharged) · GM | 1 of 20 | 3,500 rpm | 11% | 2.69 |
30 psi, single turbo
| Engine | Rank | Efficient from | Lowest surge margin | Peak PR |
|---|---|---|---|---|
| M113 (5.0 / 5.4, Kompressor) · Mercedes | 1 of 20 | 4,000 rpm | 9% | 3.25 |
| LT4 (supercharged) · GM | 1 of 20 | 3,500 rpm | 10% | 3.25 |
| LT1 (Gen V) · GM | 1 of 20 | 3,500 rpm | 10% | 3.25 |
| LS2 · GM | 1 of 20 | 4,000 rpm | 8% | 3.25 |
| L76 / L77 (6.0 Gen IV) · GM | 1 of 20 | 4,000 rpm | 8% | 3.25 |
| LS6 · GM | 1 of 20 | 4,000 rpm | 0% | 3.25 |
| LS1 · GM | 1 of 20 | 4,000 rpm | 2% | 3.25 |
| 5.7 Hemi (Eagle, VVT 2009+) · Chrysler | 1 of 20 | 4,000 rpm | 5% | 3.25 |
Assumptions (the matcher's defaults): stock torque-curve VE shape scaled to 92% peak, full boost from 3,500 rpm to redline, 120 °F charge after the intercooler, 77 °F ambient at sea level, 1.5 psi charge-side and 0.5 psi inlet losses, gasoline. A compressor map says nothing about spool or transient response; the turbine housing decides much of that. The interactive turbo matcher opens once map review is complete.
Turbine housings
The maker's turbine flow chart for this frame lists 1 housing. Highest corrected gas flow digitised for each:
| Housing | Max corrected flow (lb/min) | At expansion ratio |
|---|---|---|
| 84 trim T4 1.01 A/R | 43.1 | 2.75 |
Expansion ratio and flow as labelled on the maker's chart. See A/R ratio for how housing size trades spool against top-end flow.
Maker's published spec
- Family
- G-Series
- Bearing
- 10mm ceramic dual ball bearing
- Compressor wheel
- 73 mm inducer, 91 mm exducer
- Turbine housing A/R
- 1.01, 1.15, 1.28
- Maker's engine size range
- 2.0L-7.0L
Compare
Related
How these numbers are made
- Digitised from
- Garrett G-Series G42-1200 compressor map (lb/min and kg/s axes), linked from the G42-1200 (standard) product page https://www.garrettmotion.com/racing-and-performance/performance-catalog/turbo/g-series-g42-1200/ (Garrett Motion, retrieved 2026-10-25)
- Method
- manual reading from the maker's published map image at 1714x2048 px, assisted by row-wise dark-pixel crossing scans on a calibrated pixel grid (axis ticks located to +/-1 px)
- Accuracy
- about +/-1.5% of axis span on surge, left/lower island branches and speed lines; about +/-3% of axis span on the near-choke right-hand island sides (drawn dashed by Garrett and overlapped by labels)
- Flow correction
- 302.8 K, 96.18 kPa. Not printed on this map image (Garrett's current web maps carry no correction footnote and none was found on garrettmotion.com). Values are Garrett's long-standing convention printed on its legacy GT-series compressor maps: 545 degR (85 degF) and 13.95 psia. Treat as assumed, not maker-stated for this map.
- Pressure-ratio basis
- Not stated on the maker's map
Every figure on this page is a modelled estimate derived from that digitisation. It is not a flow-bench or dyno result and makes no power claim.
Sources
- Garrett Motion: compressor map retrieved 2026-10-25
- Garrett: product page retrieved 2026-10-25
Garrett and model names are trademarks of their owners and identify the part only. No affiliation or endorsement is implied.

